Thank you to the guys at HEGE supporting Badcaps [ HEGE ] [ HEGE DEX Chart ]
Announcement
Collapse
No announcement yet.
User Profile
Collapse
-
repair/replace solder pads
Any favourite methods of fixing adrift/missing pads ?
-
Re: ACPI Controller
And they vote for the current mob if you ever wondered who did........
-
Re: ACPI Controller
Ho hum... of course the board wont start at all now musta cooked the chip will wait until I get new chip.......
Leave a comment:
-
Re: ACPI Controller
Have ripped off PLCC32 and replaced it with a socket whle I await another programmed chip to arrive
Er...does anyone forsee any problems with this?Last edited by kiddznet; 07-09-2011, 02:52 PM.
Leave a comment:
-
Re: ACPI Controller
Next time i run the board I will put up a photo of the power bios page, I cant find any reference to disabling ACPI
Leave a comment:
-
Re: ACPI Controller
[B]severach [/B]you sound as if you have some nice hot air kit
If you dont mind what is it?Re: ACPI Controller
[B]severach [/B]you sound as if you have some nice hot air kit
If you dont mind what is it?Re: ACPI Controller
[B]severach [/B]you sound as if you have some nice hot air kit
If you dont mind what is it?
Leave a comment:
-
Re: ACPI Controller
There would one person in the world that stuff would not work for and that's me.
$28 bucks packet does 8-10 chips
Leave a comment:
-
Re: ACPI Controller
pfrcom I hear ya. This is a hobby for me wastes plenty of time for small outay!
here i have ground off a PLCC32 chip with a Dremel.About five minutes careful but no sweat work
Next flick off stubs with a small iron and clean up
[URL=http://*************/photo/my-images/684/img0187medium.jpg/][/URL]
Leave a comment:
-
Re: ACPI Controller
Thank you
tried overnight batteries removal and cmos dump
Same problem
I cant believe there is no solution on Google!
Leave a comment:
-
Re: ACPI Controller
This has worked for me
A scalpel can be used to cut the legs of the EEPROM, I use an oil stone to flatten the cutting edge of the blade at the tip . Its possible to angle the blade so that the cutting edge falls directly on to the top of the next pin as it cuts the preceding pin.
Care must be taken to ensure that you are not hitting the board surface during the process. The flattened tip helps avoid track damage in the event of a mishap, but direct contact between blade and board surface should be avoided.
The reason for cutting...
Leave a comment:
-
Re: ACPI Controller
Thank you
PLCC 32 soldered in tricky but do-able
Leave a comment:
-
Re: ACPI Controller
Thank you
I got 1 stick of ram in it keyboard and thats it
PSU known to be good
Leave a comment:
-
Re: ACPI Controller
Thank you
Nothing works
Replace bios chp?Last edited by kiddznet; 06-30-2011, 06:48 PM.
Leave a comment:
-
Re: ACPI Controller
Thank you,
Board is bare sitting on a phone book
How woud I run Memtest when I cant start the board?
Boot doesnt go past second screen device managers
Cannot load floppyLast edited by kiddznet; 06-30-2011, 03:58 PM.
Leave a comment:
-
ACPI Controller
I have here an AOpen s661fxm 7s that will not boot past the device manager display and stops at ACPI Controller
This is before Floppy and CDROM so i've no chance to reflash it as far as i can see
I can get into the biospage but can see no way of disabling ACPI
Any ideas?
What next?
-
Re: Tweaking WINXP 32
Thanks all. Good stuff there. am now using antispy very user friendly. Have been using an nlite file for a while now.
Leave a comment:
-
Tweaking WINXP 32
Whats your favourite software/reference web site for ironing out kinks and tweaks in WINXP?
-
Re: EPROM [BIOS] Programmers - What's good?
Can anyone help out with a trace/circuit diagram around a SPI bios chip on a GA-M61SMES2?
Leave a comment:
-
Re: EPROM [BIOS] Programmers - What's good?
Oh dear more drama on removing 8 pin SOP
Desoldering I was a little bumfisted and pulled 2 solder pads off
They are pad six and seven. Can see the trace to six but none for seven
Have I had some luck and seven is unused?[
IMG][URL=http://img846.*************/i/200921495615max25l6405m.jpg/][/URL] Uploaded with [URL=http://*************]*************[/URL][/IMG]Re: EPROM [BIOS] Programmers - What's good?
Oh dear more drama on removing 8 pin SOP
Desoldering I was a little bumfisted
Leave a comment:
-
Re: EPROM [BIOS] Programmers - What's good?
How about spinning CPU fan, both h/sink on CPU and northbridge getting warm, beeps for no RAM but still no boot ?
Leave a comment:
No activity results to display
Show More
Leave a comment: