Maximum speed should be marked on network ports

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • japlytic
    Badcaps Legend
    • Oct 2005
    • 2086
    • Australia

    #1

    Maximum speed should be marked on network ports

    I noted that a number of consumer entertainment devices have the maximum speed marked on the wired network port and considering that there are broadband plans faster than 100 Mbit, the wired network port can be a bottleneck since some routers do not have Gigabit (only 100 Mbit) support for the WAN port let alone the wired network ports.

    One other thing: Certain low cost network cables only have two pairs which limits speed to 100 Mbit.​
    My first choice in quality Japanese electrolytics is Nippon Chemi-Con, which has been in business since 1931... the quality of electronics is dependent on the quality of the electrolytics.
  • stj
    Great Sage 齊天大聖
    • Dec 2009
    • 30930
    • Albion

    #2
    most devices other than gaming pc's cant really shift data faster than 100Mb over the card even if it's gigabit so it's not much of a concern.
    when i did network testing i used an old SGI computer just so i could use a 64bit network adapter.

    the cables are a different matter - i have never seen a cable with only 2 pairs - not even the crap you get free with a router from the isp!

    Comment

    • lti
      Badcaps Legend
      • May 2011
      • 2545
      • United States

      #3
      I haven't seen them either, but I have seen fake "Cat6" cables that weren't twisted pair. The ISP-provided cables are at least legitimate Cat5e and have no problem handling gigabit. I wouldn't be surprised if there were Amazon scammers selling cables with only two pairs and four dummy wires (empty plastic tubes to fill the RJ45 connectors for looks) labeled "Cat8" or something else that doesn't exist.

      Comment

      Related Topics

      Collapse

      • davg
        Home network connection problem
        by davg
        I just bought a new ThinkPad laptop and I need to connect it to my home network. I have several computers on my network and can see each other in File Explorer and the older ones can communicate with each other (even with the new one) but the ThinkPad can see the other computers but can't communicate with them. I get the (network error 0x80070035 The network path not found). I tried several scenarios that I found on line but none of them worked?? Since the other computers on the network can communicate fine I'm assuming the problem is with the setup of the ThinkPad? All computers are running Windows...
        03-06-2021, 07:13 AM
      • trepachka
        Help me identify the component for Thinkpad E15 Gen 2 - NS-D013 - daughter board
        by trepachka
        I have the schematics for the motherboard (NM-D011) but not the daughter board (NS-D013) which is responsible for power button, fingerprint reader, wired network, etc.

        I found this diode marked '5AE2D" partially shorted. On the board it is marked as U0302. Can someone, please tell me the actual diode name so that I order a replacement for it?

        Thanks....
        01-16-2024, 07:46 PM
      • Maniackk
        Reader PocketBook InkPad 3 – identification of a black component marked 'CT' on the microUSB line
        by Maniackk
        Hello,

        Device: PocketBook InkPad 3
        Mainboard: XRZ_E091_PB740-VTTOA-V1.1 / 2017-10-12

        I'm replacing the broken microUSB connector on this e-reader, and during inspection after desoldering, I noticed a loose black SMD component marked "CT". One of them was torn off along with the pad, while the other one (marked in the photo) is still in place.

        I would appreciate help identifying this component.

        Measuring the loose component with a multimeter gives 5.84 MΩ in both directions, while the one still on the board shows no measurable...
        05-16-2025, 08:53 AM
      • harp
        simple win network with optimization issue
        by harp
        simple win network with optimization issue I like to ask some question about configuring simple room win network. So, there is 2 win computer, android4 device and wifi router not connected to internet. The purpose is storage space and manipulation with large files between any device. 1 pc - 192.168.0.2 (winxp sp2) wired to router port#1 2 pc - 192.168.0.5 (win10, enabled smb1.1) wired to router port#2 3 router - 192.168.0.1 with dhcp for wifi (192.168.0.101...) 4 main tablet - 192.168.0.101 (android4) wified to router wifi port I generally work and control transfer with my tablet via ES3 file...
        Today, 11:01 AM
      • BOSCHNJAK
        by BOSCHNJAK
        ABOUT ME INTRODUCTION FILE

        2
        024 BEV, BIH, SARAJEVO START PROJECT: ELECTRIC VEHICLE TOYOTA 4 RUNNER CONVERSION http://www.bev.ba/TOYOTA4RUNNER/index.html

        2023 BEV, BIH, SARAJEVO START PROJECT: SECRETS AND MANUFACTURING PLANS (AS MY REPLICA) OF THE LIBERTY ENGINE 2.0.
        2022 BEV, PROJECT ?
        2021 BEV, PROJECT ?
        2020 BEV,BiH, Sarajevo: PROJECT IS: HOW TO SWITCH OFF PERMANENT MAGNET FIELD and HOW TO SWITCH ON PERMANENT MAGNET FIELD?
        2019 BEV, Croatia, Ston:, Broce: PROJECT - PROJEKT ELEKTRIČNI GLISER http://www.bev.ba/ELEKTRICNIVANBRODSKIMOTOR/indexHR.htm...
        12-28-2023, 02:09 PM
      • Loading...
      • No more items.
      Working...