BenQ T705, no backlight

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • munuainen
    Member
    • Jul 2010
    • 40

    #1

    BenQ T705, no backlight

    Hi there.

    I just recently got a T705 that was reported having no image. I've been searching for information on the issue and found plenty. However, I'm pretty much a beginner in the field of monitor repair so I could use some advice.

    What I've discovered/done so far:

    Power turns on and the power led green/amber states seem to be ok. The display is recognized when connected (maybe there's even a proper image but it's impossible to say without backlight working). There was no voltage in backlight connector pins when tested.

    El. caps looked fine but I've replaced most of them just in case. Caps C703, C704, C818 and C821, each 470uf 35V are yet to be replaced. The huge C605 is original as well.

    Of C5707 transistors Q808, Q809, Q815 & Q816, three were faulty (shorted or open) and one gave ohm readings Base-Emitter 2,1k, Base-Collector 450, Emitter-Collector 2,6k. I assume those are not exactly healthy readings.

    Of FU9024N mosfets Q805 & Q812, one was shorted and the other gave ohm readings: Gate-Drain 160, Gate-Source 160, Drain-Source 3. That's to be replaced too, right?

    The fuse F601 was fine, PF801 ohms were 11k. Isn't that 11k too much?

    I've also replaced solder in T801-T804 as instructed by many. I think I'll order new C824 and C826, too, as one of them was partially melted by Q808 and had a cracked soldering. Anything else I should do while waiting for replacements to arrive?
    Attached Files
  • PlainBill
    Badcaps Legend
    • Feb 2009
    • 7034
    • USA

    #2
    Re: BenQ T705, no backlight

    You've got it pretty well covered. There are some (I'm one of them) that replace all caps except the large (100uF, 450 volt?) one. There are also some who will replace that cap also, I don't claim they are wrong.

    The 4 C5707 transistors, the two FU9024N, and the fuse must be replaced. And of course, resoldering the transformers should prevent a repeat failure.

    PlainBill
    For a number of reasons, both health and personal, I will no longer be active on this board. Any PMs asking for assistance will be ignored.

    Never be afraid to try something new. Remember, amateurs built the ark. Professionals built the Titanic.

    Comment

    • el3ctroded
      Senior Member
      • Nov 2008
      • 198
      • USA

      #3
      Re: BenQ T705, no backlight

      Originally posted by munuainen
      El. caps looked fine but I've replaced most of them just in case. Caps C703, C704, C818 and C821, each 470uf 35V are yet to be replaced. The huge C605 is original as well.

      Of C5707 transistors Q808, Q809, Q815 & Q816, three were faulty (shorted or open) and one gave ohm readings Base-Emitter 2,1k, Base-Collector 450, Emitter-Collector 2,6k. I assume those are not exactly healthy readings.
      The 470 35v caps you might as well replace, especially if it doesn't work after replacing the C5707 transistors. Yes, you were likely right about those readings, especially if it was read out of circuit.


      Of FU9024N mosfets Q805 & Q812, one was shorted and the other gave ohm readings: Gate-Drain 160, Gate-Source 160, Drain-Source 3. That's to be replaced too, right?
      I don't see Q805/Q812... In any event, note that sometimes a transistor/fet/diode will read as shorted, but it will actually be the resistance of a inductor or transformer you are reading. Remove it from the circuit and retest if you read it in-circuit. If you get similar readings, then you know if it's bad.

      The fuse F601 was fine, PF801 ohms were 11k. Isn't that 11k too much?
      Yes. A fuse should be < 1 ohm.

      I've also replaced solder in T801-T804 as instructed by many. I think I'll order new C824 and C826, too, as one of them was partially melted by Q808 and had a cracked soldering. Anything else I should do while waiting for replacements to arrive?
      If you haven't already, do diode tests on all diodes, in both directions.

      Comment

      • munuainen
        Member
        • Jul 2010
        • 40

        #4
        Re: BenQ T705, no backlight

        First of all, thanks for quick replies. I forgot to mention in my opening post that all ohm values were indeed out-of-circuit readings. What kind of caps can I replace C824 and C826 with? All 22uf 160Vs I found by googling were radial electrolytics. Are those ok?

        Comment

        • jetadm123
          Badcaps Legend
          • Feb 2010
          • 2169

          #5
          Re: BenQ T705, no backlight

          Hello! There's a guy on ebay selling a repair kit for a very reasonable price:

          http://cgi.ebay.com/REPAIR-KIT-E172F...item3355ff735c

          If the link doesn't work, do a ebay search for c5707.

          He's sold over 700 of these kits! It would be funny, if it wasn't so sad.

          Comment

          • munuainen
            Member
            • Jul 2010
            • 40

            #6
            Re: BenQ T705, no backlight

            Originally posted by jetadm123
            He's sold over 700 of these kits! It would be funny, if it wasn't so sad.


            I actually bid on a similar item being sold by this person. I'll save $1 compared to using buy it now...am I stingy or what?

            Comment

            • smason
              Badcaps Legend
              • Feb 2010
              • 1652
              • Canada

              #7
              Re: BenQ T705, no backlight

              Originally posted by jetadm123
              Hello! There's a guy on ebay selling a repair kit for a very reasonable price:

              He's sold over 700 of these kits! It would be funny, if it wasn't so sad.
              I bought 2. So far....
              36 Monitors, 3 TVs, 4 Laptops, 1 motherboard, 1 Printer, 1 iMac, 2 hard drive docks and one IP Phone repaired so far....

              Comment

              • retiredcaps
                Badcaps Legend
                • Apr 2010
                • 9271

                #8
                Re: BenQ T705, no backlight

                A tip for those buying these "kits".

                I found that some of these ebay sellers will do "custom" kits. So if you need more c5707 or less/more picofuses, send them an email and ask for a custom kit and some will do it for you.

                I bought my own c5707/fu9024/3a 125v fuse (4 kits) from an ebay seller for about the same price as one kit.

                Originally posted by smason
                I bought 2. So far....
                --- begin sig file ---

                If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

                We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

                Please do not post inline and offsite as they slow down the loading of pages.

                --- end sig file ---

                Comment

                • munuainen
                  Member
                  • Jul 2010
                  • 40

                  #9
                  Re: BenQ T705, no backlight

                  Originally posted by el3ctroded
                  If you haven't already, do diode tests on all diodes, in both directions.
                  I assume you mean only the diodes visible in the front side of the PCB.

                  Again, I'll be delighted if someone can assist me with with whether box-shaped caps C824 and C826 can be replaced with radial electrolytic ones of equal specs.

                  Comment

                  • retiredcaps
                    Badcaps Legend
                    • Apr 2010
                    • 9271

                    #10
                    Re: BenQ T705, no backlight

                    Post pictures from all sides on the C824 and C826. There should be a value on the top or side. On one of my Benqs (FP71g+), it lists .22K 160. You should have something similar to that?

                    Also, Mouser, Digikey, etc will sell these type of caps.

                    Originally posted by munuainen
                    Again, I'll be delighted if someone can assist me with with whether box-shaped caps C824 and C826 can be replaced with radial electrolytic ones of equal specs.
                    Last edited by retiredcaps; 07-13-2010, 04:08 PM.
                    --- begin sig file ---

                    If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

                    We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

                    Please do not post inline and offsite as they slow down the loading of pages.

                    --- end sig file ---

                    Comment

                    • munuainen
                      Member
                      • Jul 2010
                      • 40

                      #11
                      Re: BenQ T705, no backlight

                      Originally posted by retiredcaps
                      Post pictures from all sides on the C824 and C826. There should be a value on the top or side. On one of my Benqs (FP71g+), it lists .22K 160. You should have something similar to that?
                      Thanks for the reply. Yes, both caps are .22uF 160V, similar to those in this discussion. The cap type was what I was mainly after before I found that thread. So they are metallized polypropylene film caps. Will some of these do? Is it a big crime to have a cap with voltage rating greater than the original if you can't find an exact replacement?

                      Comment

                      • retiredcaps
                        Badcaps Legend
                        • Apr 2010
                        • 9271

                        #12
                        Re: BenQ T705, no backlight

                        Originally posted by munuainen
                        Is it a big crime to have a cap with voltage rating greater than the original if you can't find an exact replacement?
                        You can go higher in voltage, but some of those caps on ebay are 650V and 2000V.

                        79 cents each at Digikey (part# 495-1278-ND)

                        http://search.digikey.com/scripts/Dk...me=495-1278-ND

                        BTW, I think the packaging of these caps can take a lot of abuse. While soldering, I accidentally touched one of these types of caps with the barrel of the iron. The plastic is slightly melted, but it still works AFAIK.

                        I don't have any experience in these types of caps, but if one of the more knowledgable members say replace, then replace them. If they say leave it alone, I would leave it alone.
                        --- begin sig file ---

                        If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

                        We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

                        Please do not post inline and offsite as they slow down the loading of pages.

                        --- end sig file ---

                        Comment

                        • munuainen
                          Member
                          • Jul 2010
                          • 40

                          #13
                          Re: BenQ T705, no backlight

                          Thanks for the digikey link. Unfortunately, international shipping costs are like $30 no matter how small the order.

                          That's why I prefer ebay as a source.

                          Comment

                          • retiredcaps
                            Badcaps Legend
                            • Apr 2010
                            • 9271

                            #14
                            Re: BenQ T705, no backlight

                            Fill out your country profile. That way, we know where you are and can suggest more appropriate suppliers.

                            Originally posted by munuainen
                            Thanks for the digikey link. Unfortunately, international shipping costs are like $30 no matter how small the order.

                            That's why I prefer ebay as a source.
                            --- begin sig file ---

                            If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

                            We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

                            Please do not post inline and offsite as they slow down the loading of pages.

                            --- end sig file ---

                            Comment

                            • lucky13
                              Badcaps Veteran
                              • Aug 2007
                              • 412

                              #15
                              Re: BenQ T705, no backlight

                              Originally posted by munuainen
                              I think I'll order new C824 and C826, too, as one of them was partially melted by Q808 and had a cracked soldering. Anything else I should do while waiting for replacements to arrive?
                              Can you post pix showing damages to these 2 caps? If just cosmetic damage, you cna leave them alone.

                              Comment

                              • munuainen
                                Member
                                • Jul 2010
                                • 40

                                #16
                                Re: BenQ T705, no backlight

                                Originally posted by lucky13
                                Can you post pix showing damages to these 2 caps? If just cosmetic damage, you cna leave them alone.
                                Only one of them had suffered damage from heat. The other is fine as far as its appearance is concerned. I just thought it'd be a minor investment to replace them as well, just in case.
                                Attached Files

                                Comment

                                • munuainen
                                  Member
                                  • Jul 2010
                                  • 40

                                  #17
                                  Re: BenQ T705, no backlight

                                  Replacement parts arrived. After soldering c5707s, fu9024s and the fuse the backlight began to work. Image was perfect. Oh joy! Thanks to everyone who contributed to this thread.

                                  Comment

                                  Related Topics

                                  Collapse

                                  • seppde
                                    Benq Zowie XL2540K / Power board failure / 6Pin-SOP-Chip identification
                                    by seppde
                                    Hello everyone,
                                    I've got a Benq power board of a XL2540K monitor which suffered from a power cut and is since defective / won't turn on. It's got obvious defects, some blown resistors, some burning around the drain pin of a MOSFET...
                                    ... and some 6-pin IC I struggle identifying, that is driving said MOSFET.
                                    The IC is labeled as IC601, so someone with a circuit schematic could probably identify it really quick, unfortunately I can't find the schematics.
                                    In other power boards of Benq for which I did find the schematics, IC601 is an 8-pin NCP1200 PWM controller - I suppose...
                                    02-09-2024, 05:19 AM
                                  • AJ847.63e
                                    BenQ TH681 Originally overheating now wont fire the lamp - Colour wheel not starting
                                    by AJ847.63e
                                    Hi All.

                                    Does anyone have any reference materials or something I can use to try troubleshooting a BenQ TH681? Google unfortunately has turned up zip. I did find a service manual for a W series BenQ but that is pretty much useless, it's more a glorified user manual. A list of voltages would be great as I suspect my mainboard is faulty, the colour wheel voltage is not dipping like it should.

                                    The one I am troubleshooting now was originally overheating after a lamp replacement. It originally would take 2 minutes or so for it to shut off and blink the temp and lamp lights...
                                    09-18-2023, 06:42 PM
                                  • ChatBTC
                                    Benq EX3501R
                                    by ChatBTC
                                    Hi!

                                    I am new to this site, and found it via LLM ChatGPT.

                                    I got a BenQ Ex3501R monitor which i have had for a while now, it works pretty good until recently, it struggles to turn on, i can see the purple welcome screen is shown for a brief time before it vanish again, usually it stays on for a couple of seconds before the main computer screen is shown, but image is still kept black, before i just had to turn it off and on a few times and that would leave it on, but now it takes ever longer to stabilize the image on the screen, ocasionally i can see the computer desktop...
                                    01-24-2025, 08:49 PM
                                  • Document Archive
                                    BenQ JoyBook S52 S53 Laptop Schematic
                                    by Document Archive
                                    BenQ JoyBook S52 S53 Laptop Schematic
                                    Quanta ED3...
                                    11-01-2024, 02:03 PM
                                  • Document Archive
                                    BenQ S72 Laptop Schematic
                                    by Document Archive
                                    BenQ S72 Laptop Schematic
                                    Inventec Grasshopper Rev 3.0...
                                    11-01-2024, 07:23 AM
                                  • Loading...
                                  • No more items.
                                  Working...