emachines e19t6w inverter powersupply help

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • jselvatici
    Member
    • May 2010
    • 25

    #81
    Re: emachines e19t6w inverter powersupply help

    Originally posted by retiredcaps
    PS. I tested this on a working LCD. If I put my black on a ground screw on the secondary side and red on the middle pin of my dual diode, I get 5V DC.

    Looking at page 69 of the schematics (vx1945wm-3.pdf), pins 8 and 9 go right into D805. You should get 5V DC. If not, either the diode is bad or the transformer isn't working.

    You can double check the dual diode by using the diode check on your multimeter. Test it like any normal diode. I believe the middle pin is your negative.
    Okay,

    D805 there's no 5V DC on it. and the transformer is not provinding any voltage. D803 has the same behavior.

    I did the diode check on both and the results are:
    D805 -> Between 1 and 2 = 0,150 ohm and is the same for 3 and 2.
    also, if you go in the reverse way, the multimeter is giving me 1.520 ohms. Is not suppose to not conduct in this way? or is this type of diode?

    D803 -> Between 1 and 2 = 0,300 ohm and is the same for 3 and 2.
    Nothing on reverse way with multimeter in diode test scale.

    So, we have to move before these diodes right? The transformer? or before it?

    What about AP2761? (Q804) It was shorted in the very beggining and I replace it by K2843 (because in the components store, they told me that was compatible, is not?)

    Tks.

    Comment

    • retiredcaps
      Badcaps Legend
      • Apr 2010
      • 9271

      #82
      Re: emachines e19t6w inverter powersupply help

      Originally posted by jselvatici
      I did the diode check on both and the results are:
      D805 -> Between 1 and 2 = 0,150 ohm and is the same for 3 and 2.
      also, if you go in the reverse way, the multimeter is giving me 1.520 ohms. Is not suppose to not conduct in this way? or is this type of diode?

      D803 -> Between 1 and 2 = 0,300 ohm and is the same for 3 and 2.
      Nothing on reverse way with multimeter in diode test scale.
      I think those readings look correct.

      So, we have to move before these diodes right? The transformer? or before it?
      From the schematics, pin 8 and 9 go right into D805. There is nothing else "before" it. And you get 308V DC on pin 1 and 3 (which is correct).

      I believe this provides more evidence that the transformer is not working properly on the secondary side.
      --- begin sig file ---

      If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

      We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

      Please do not post inline and offsite as they slow down the loading of pages.

      --- end sig file ---

      Comment

      • jselvatici
        Member
        • May 2010
        • 25

        #83
        Re: emachines e19t6w inverter powersupply help

        Originally posted by retiredcaps
        I believe this provides more evidence that the transformer is not working properly on the secondary side.
        I have the same clue... But I was checking for the transformer, and this SPW-055 is not so easy to find.

        Here where I live, will be much harder..

        Something else to check before goes to transformer replacement?

        Tks!

        Comment

        • retiredcaps
          Badcaps Legend
          • Apr 2010
          • 9271

          #84
          Re: emachines e19t6w inverter powersupply help

          Originally posted by jselvatici
          Something else to check before goes to transformer replacement?
          I would suspect the SMPS controller (NCP1337), but you have already replaced it twice (once from initial damage and again after voltage testing/short).

          The only other thing I can think of is IC801, the optoisolater. It provides feedback from the secondary side back to the primary side. Pin 2 goes right into NCP1337.

          Test Pin 1 and 2 like a diode. Pin 3 and 4 should have 0.3 ohms resistance. Resitance between 1 to 4 and 2 to 3 should read inifinite ohms.
          --- begin sig file ---

          If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

          We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

          Please do not post inline and offsite as they slow down the loading of pages.

          --- end sig file ---

          Comment

          • retiredcaps
            Badcaps Legend
            • Apr 2010
            • 9271

            #85
            Re: emachines e19t6w inverter powersupply help

            Also, on pin 4 of the transformer, it goes to D804. From D804, it goes on pin 6 of NCP1337. Last time, you measured pin 6 it was 0V DC. This didn't look right to me initially.

            So retest diode D804 with the diode test and make sure it works. Then measure the voltage on D804.

            Again, I'm using page 69 schematic for reference.
            --- begin sig file ---

            If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

            We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

            Please do not post inline and offsite as they slow down the loading of pages.

            --- end sig file ---

            Comment

            • pedro
              Senior Member
              • Dec 2009
              • 199
              • AUSTRALIA

              #86
              Re: emachines e19t6w inverter powersupply help

              Originally posted by retiredcaps
              The only other thing I can think of is IC801, the optoisolater. It provides feedback from the secondary side back to the primary side. Pin 2 goes right into NCP1337.

              Test Pin 1 and 2 like a diode. Pin 3 and 4 should have 0.3 ohms resistance. Resitance between 1 to 4 and 2 to 3 should read inifinite ohms.
              ??? Without going off chasing the opto's details, if 1 & 2 are the LED (most common in 4-pin DIP optos) and 3,4 are the transistor then 3,4 should certainly NOT measure 0.3 ohms. It should be a very high reading both ways.
              Friends don't let friends buy Samsung ....

              Comment

              • retiredcaps
                Badcaps Legend
                • Apr 2010
                • 9271

                #87
                Re: emachines e19t6w inverter powersupply help

                Originally posted by pedro
                ??? Without going off chasing the opto's details, if 1 & 2 are the LED (most common in 4-pin DIP optos) and 3,4 are the transistor then 3,4 should certainly NOT measure 0.3 ohms. It should be a very high reading both ways.
                Good catch. I meant NOT 0.3 ohms. It's hard flipping back and forth on one monitor!

                Also, I made a typo on the pin going to the NCP1337. It is pin 3 of the opto that goes pin 2 of the NCP1337.
                --- begin sig file ---

                If you are new to this forum, we can help a lot more if you please post clear focused pictures (max resolution 2000x2000 and 2MB) of your boards using the manage attachments button so they are hosted here. Information and picture clarity compositions should look like this post.

                We respectfully ask that you make some time and effort to read some of the guides available for basic troubleshooting. After you have read through them, then ask clarification questions or report your findings.

                Please do not post inline and offsite as they slow down the loading of pages.

                --- end sig file ---

                Comment

                • jetadm123
                  Badcaps Legend
                  • Feb 2010
                  • 2169

                  #88
                  Re: emachines e19t6w inverter powersupply help

                  Originally posted by jselvatici
                  No luck my friend...

                  I change the FET, Resistor, the Fuse and the 47uF Cap and no 5VDC in the output...

                  Any new idea?
                  When you changed R805 what value did you use? The schematic says 0.18 ohms at 2 Watts. I'm asking because initially looking at the photo of the resistor I thought it was 18 ohms.
                  Last edited by jetadm123; 08-29-2010, 02:22 PM.

                  Comment

                  • jselvatici
                    Member
                    • May 2010
                    • 25

                    #89
                    Re: emachines e19t6w inverter powersupply help

                    Originally posted by jetadm123
                    When you changed R805 what value did you use? The schematic says 0.18 ohms at 2 Watts. I'm asking because initially looking at the photo of the resistor I thought it was 18 ohms.
                    Well, now I have 0.24 ohms resistor (Is exactly the same as the original that was installed before).

                    Facing this resistor, my board don't look like the one in the file vg1930wm-1_sm.pdf ?? (Page 62)

                    tks.

                    Comment

                    • jetadm123
                      Badcaps Legend
                      • Feb 2010
                      • 2169

                      #90
                      Re: emachines e19t6w inverter powersupply help

                      Originally posted by jselvatici
                      Well, now I have 0.24 ohms resistor (Is exactly the same as the original that was installed before).

                      Facing this resistor, my board don't look like the one in the file vg1930wm-1_sm.pdf ?? (Page 62)

                      tks.
                      Just a minute.... In post #55 you show a photo of the original R805, which according to it's color code is .18 ohms. Now your saying the original was .24 ohms?

                      Comment

                      • jselvatici
                        Member
                        • May 2010
                        • 25

                        #91
                        Re: emachines e19t6w inverter powersupply help

                        Originally posted by jetadm123
                        Just a minute.... In post #55 you show a photo of the original R805, which according to it's color code is .18 ohms. Now your saying the original was .24 ohms?
                        Yeap.

                        Because in the very beggining I have just that on hands...

                        After that blows up, I bought the exactly one that the board has...

                        Do you think that are problems with this difference?

                        many tks!

                        Comment

                        • drdbrown
                          New Member
                          • Oct 2010
                          • 2

                          #92
                          Re: emachines e19t6w inverter powersupply help

                          I fixed this โ€œshutdown after a few secondsโ€ problem on a Viewsonic VA1930 by replacing the electrolytic caps on the power board and re-soldering the power transformer joints (SPW-055). A startup buzzy noise was coming from the transformer, and I found that if it was torqued slightly the noise would stop leading me to the cold solder joints which must have been caused due to their large posts that were not heated up enough during construction. Who knows, perhaps the bad jointโ€™s extra resistance caused a cap to overheat (the large, 1000mf one was swollen and leaking) because after replacing them the squealing was stronger and allowed a longer running time to locate the cold joint.

                          BTW: The transformer still has a 1 second squeal when first powered up then all is quiet as the backlights are working. I know most of these circuits have a high voltage startup surge to light up the CFLs which then drops after a second to running voltage, the circuitry then tests the voltages to see if they are nominal and shuts down if they are wrong. I wonder if anyone out there with this board has noticed the same one second startup squeal. If not, I might have a bad winding and my fix is temporary. Anyone?
                          David
                          (ps. Thanks for all the hints in this thread!!!)

                          Comment

                          Related Topics

                          Collapse

                          • Document Archive
                            ACER eMachines PT.NCAE2.071 eMachines EL1850 E5800 Specification for Upgrade or Repair
                            by Document Archive
                            This specification for the ACER eMachines PT.NCAE2.071 can be useful for upgrading or repairing a desktop PC that is not working. As a community we are working through our specifications to add valuable data like the eMachines PT.NCAE2.071 boardview and eMachines PT.NCAE2.071 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet,...
                            09-12-2024, 03:36 PM
                          • x_orange90_x
                            Vizio E55-E1 bad backlights or bad inverter?
                            by x_orange90_x
                            I just got this tv today and it appeared to have no backlight on. After taking off the rear cover and checking again in the dark I can see that MAYBE one quadrant is lit.. But still it's quite dim. I was going to check the LEDs with my tester, and I found LED 1 and LED 2 + pins on the wire from the inverter, but I couldn't identify a ground. Nonetheless I tried using a mounting screw on the inverter board and also the chassis as ground but regardless my tester reads 300 which is what it reads when there is no voltage draw.

                            I don't know how exactly to test the inverter itself. Is it...
                            01-29-2025, 09:24 PM
                          • grimacelord
                            OLD eMachines T6520 BIOS Request!
                            by grimacelord
                            Hello,

                            I know that this is probably a long shot, but I figured if anyone could find this BIOS, it would be you guys.

                            I am working on an (old) eMachines T6520 desktop PC that might have a corrupt BIOS.

                            Model:
                            eMachines T6520

                            Motherboard markings:
                            MS-7145B0505068731
                            RS480M
                            7145 v2.1 RS480-A21+SB400-A23

                            Symptoms:
                            The computer does power on, CPU fan spins, but does not POST. No display.

                            Troubleshooting steps so far:
                            Replaced the CMOS battery (which was in need of replacing)
                            Re-seating...
                            01-12-2024, 12:43 PM
                          • Document Archive
                            Acer eMachines EM355-131G25ikk Netbook 350 Specification for Upgrade or Repair
                            by Document Archive
                            This specification for the Acer eMachines EM355-131G25ikk Netbook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the EM355-131G25ikk boardview and EM355-131G25ikk schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet,...
                            09-06-2024, 05:27 AM
                          • Gentian
                            APSINT3636VR 3600W APS INT Series 36V DC 230V AC Inverter/Charger schematic
                            by Gentian
                            I have a tripp-lite aspint 3636vr inverter charger which blow some of mosfet transistors. I replaced them repaired also the driver circuit and tested but the mosfets burn again.

                            It work very well as inverter and also as charger if I let the rear switch in auto mode (inverter) and charger only(charging) but in auto when I connect the feed line 220V AC first time it pass ok to line and start charging the batteries but when I remove the feed line it pass to inverter mode and if I do it again the second time when passing from charging to inverter the Main transformer start making a...
                            03-06-2023, 07:07 AM
                          • Loading...
                          • No more items.
                          Working...