Hanns-G hw173d

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • sakpase
    New Member
    • Mar 2013
    • 1
    • Philippines
    #1

    Hanns-G hw173d

    hi guys yesterday i have a problem with my hanns g lcd 17 inch
    i thought my gpu is messing up my screen because sometimes my screen is going blank so i checked my video card and test it to another pc and it works ok
    then i googled my lcd and check and i read something about the lcd bulb need to change and i bought lcd bulb and replace the old one with the new lcd bulb i bought. now i have a problem again my screen is totally blank when i switch off and switch on again my lcd power turns green and after a seconds it turns orange cant see display its totally blank screen.
    Tags: None
    • budm
      Badcaps Legend
      • Feb 2010
      • 40746
      • USA
      #2
      Re: Hanns-G hw173d

      "my lcd power turns green and after a seconds it turns orange cant see display its totally blank screen" It either the monitor is not getting the signal from the video card so it goes into standby mode (orange light), or it goes into shutdown mode.
      Any good clear pictures of the boards?
      Never stop learning
      Basic LCD TV and Monitor troubleshooting guides.
      http://www.badcaps.net/forum/showthr...956#post305956

      Voltage Regulator (LDO) testing:
      http://www.badcaps.net/forum/showthr...999#post300999

      Inverter testing using old CFL:
      http://www.badcaps.net/forum/showthr...er+testing+cfl

      Tear down pictures : Hit the ">" Show Albums and stories" on the left side
      http://s807.photobucket.com/user/budm/library/

      TV Factory reset codes listing:
      http://www.badcaps.net/forum/showthread.php?t=24809

        Comment

        Previous template Next

        Related Topics

        Collapse
        • repair-it
          TOSHIBA DLP 52HM95 How to reset timer module on bulb
          by repair-it
          I replaced the bulb only on my Toshiba DLP The bulb is a TB-25. This is the first time I've done a bulb only replacement. Supposedly there is a timer module that needs to be re-calibrated or reset. I don't know where the module is located. I see some vendors selling the bulb with the housing stating module included which leads me to think the module is located inside the enclosure the bulb mounts in, but I didn't see it. Maybe it's inside the plug attached to the bulb?

          Anyway - I am seeking information on how to reset this so called module so that the lamp will operate. Apparently...
          10-11-2023, 07:18 PM
        • ezenia
          LUMIMAN Smart Bulb IC ID?
          by ezenia
          Hi,

          I have a LUMIMAN Smart Bulb that suddenly stopped lighting one day. The bulb is still detected in the app, but won't light. I've probed around and nothing seems to look off with any of the diodes, caps or resistors. The Bluetooth/Wi-Fi module seems to be working as it's still detected in the app. I even tried deleting and re-pairing the bulb (it didn't light, but I was still able to follow the pairing instructions), it re-paired fine, but still no light.

          In diode mode, the LEDs all light up when probed so I'm guessing this means the LEDs themselves are OK. I was expecting...
          04-28-2025, 05:56 PM
        • hasel17
          CH341a can erase and read but can't write and blank check
          by hasel17
          So I am trying to repair broken thunderbolt FW on X1 Yoga Gen 2. The EEPROM chip is WINBOND 25Q80DVNIG. I already do a back-up and erase. But when I try to wrote new FW, it was successfull, but when I tried to read it, it still blank. when I try to do a blank check, it gave me instant error in address 0. I already tried two CH341A, already did the 3.3v fix mod, using AsProgrammer, NeoProgrammer, Colibri, and CH341A 1.29. But the problem still occurred. What I did wrong here? Can anyone help me? Thanks in advance. Here is the log in Colibri :

          Code:
          Checking for blank...
(Press
          ...
          10-26-2023, 06:20 AM
        • JimBanville
          Replacing incandescent bulb on Pioneer LD player with led. Need help :)
          by JimBanville
          I have a pioneer dvl-909 LD/dvd player from 1998. It has a light on the front panel that lights up when you play a dvd. I removed the bulb and it appears to be a tiny incandescent bulb. Its measures "open"/dead and the bulb is black like it's blown. The socket it fits into measures 5v. I've looked up the schematics and there's no indication of the amperage. I don't want to spend any money on new parts, but I have a pack of like 100, 3v, 20ma LEDs and I have various resistors.
          Is there a way for me to determine the amperage going to the old dead bulb with my multimeter?
          ...
          01-24-2023, 07:49 AM
        • RetroComputingGrotto
          Hanns.G Hi221 Monitor - Works For A Second & Then Blank Display
          by RetroComputingGrotto
          I've got a Hanns.G Hi221 Monitor that works for a moment and then the display goes off but the power LED indicator remains on. If you power it off and back on again it does the same thing, it comes on and then the display goes blank. From a cold start it takes 10 seconds or so before the display goes blank but if you turn it off and then back on again after it already being on it goes blank a lot quicker so I'm assuming something is getting hot which is causing the display to go off.

          I've uploaded a video of it happening on YouTube:



          I've taken the monitor...
          01-11-2024, 05:37 AM
        • Loading...
        • No more items.
        Working...