TM-0915 transformer

[dcooke570]

Samsung Syncmaster 2233RZ
Tried replacing capacitors with new ones.

Screen still shuts off after 2 seconds.
Can see the screen still with flash light.

Removed the transformer and tested the secondaries.
1st pair: 854
2nd pair: 902

So they are just barely within 3%.
Anything more definitive I can test for or just order a new one?

I have pics just can't post them from this iPod.

Dan

[budm]

Re: TM-0915 transformer

Try test lamp, such as this: https://www.badcaps.net/forum/showthread.php?t=19987
or T5 4WATTS lamps.
or inspect the lamps and wiring.
http://s807.photobucket.com/albums/y...klight%20lamp/

[Nocta]

Re: TM-0915 transformer

What about mosfets and transistors? Are they working?

[retiredcaps]

Re: TM-0915 transformer

Removed the transformer and tested the secondaries.
1st pair: 854
2nd pair: 902

So they are just barely within 3%.

1) For most of the time, you don't have to remove the transformer to measure the resistance of the secondaries.

2) I always do the math this way. If 854 is the "correct" reading, then

854 x 0.97 = 828.38
854 x 1.03 = 879.62

So if the second transformer falls in between the two above numbers, then it is good.

3) Before buying a new transformer, do the ccfl test and examination as suggested by budm. If your transformer readings were 854 and 1500, then it is more obvious what is wrong.

[retiredcaps]

Re: TM-0915 transformer

BTW, this person had a 2 seconds to black problem (same monitor), but his transformer readings were more obvious.

https://www.badcaps.net/forum/showth...hlight=tm-0915

[dcooke570]

Re: TM-0915 transformer

I don't have access to spare pink or blue connectors for the ccfl test. The connector is pretty tiny to get anything in there to make the connection with anything else. What type of connection could I use in place of the pink/blue connectors?

[budm]

Re: TM-0915 transformer

You can solder the wires directly to the connectors on the board, you can see the two pins per lamp on the soldered side of the board.

[dcooke570]

Re: TM-0915 transformer

What gauge wire do you recommend to solder to the connector?

[budm]

Re: TM-0915 transformer

24AWG should be fine, or even 26AWG.

[dcooke570]

Re: TM-0915 transformer

Try test lamp, such as this: https://www.badcaps.net/forum/showthread.php?t=19987
or T5 4WATTS lamps.
or inspect the lamps and wiring.
http://s807.photobucket.com/albums/y...klight%20lamp/

OK, bought a 3 pack of 14w cfls and hooked one up to the inverter board. Same result; cfl lights for 2 then goes off like the screen did.

Anything else to test before ordering the transformer?

[retiredcaps]

Re: TM-0915 transformer

Anything else to test before ordering the transformer?

My checklist (regulars may skip the URL below)

More details starting with post #19 at

https://www.badcaps.net/forum/showthread.php?t=10419

[selldoor]

Re: TM-0915 transformer

hooked one up to the inverter board.

I am assuming your panel has more than one lamp and if so you should
be using the test lamp in turn with each lamp. As I recall it explains this in
retiredcaps guide quoted above.

[dcooke570]

Re: TM-0915 transformer

I am assuming your panel has more than one lamp and if so you should
be using the test lamp in turn with each lamp. As I recall it explains this in
retiredcaps guide quoted above.

My bad. 4 lamps. The 2 connectors on the side where the push button connector is are the ones that turn on 2 seconds. The other 2 connectors are not lighting the test lamp at all.

[budm]

Re: TM-0915 transformer

So is this a single transformer setup or two transfromers, one per two lamps? If it is two lamp setup, then I would swap the working one with the one that does not light up the lamp, if the problem follows, then you have bad transformer, if the same two lamps still do not light with the know good transformer, then more components in that section will have to be investigated.

[dcooke570]

Re: TM-0915 transformer

So is this a single transformer setup or two transfromers, one per two lamps? If it is two lamp setup, then I would swap the working one with the one that does not light up the lamp, if the problem follows, then you have bad transformer, if the same two lamps still do not light with the know good transformer, then more components in that section will have to be investigated.

Single transformer (one tm-0915). Each lamp will light for 2 sec if I plug them in to the connector near the push button connector.

[budm]

Re: TM-0915 transformer

If it is single transformer, then that will eliminate the transformer driving circuits problem since the primary winding is driven by single circuit, so it does look like you do have one bad secondary. Are there four small blue caps close to the secondary side of the transformers that lead to the lamp connectors?

[retiredcaps]

Re: TM-0915 transformer

http://www.ebay.com/itm/150861446003

[dcooke570]

Re: TM-0915 transformer

Yes, there are the 4 small blue caps.

[budm]

Re: TM-0915 transformer

Please use the Ohm meter set to the highest scale and see if they are leaking on that bad section.
Let me see if I have the transformer at the recycling place, I will be working there tomorrow.
I save some boards from monitors with broken screen.
http://s807.photobucket.com/albums/y...pply%20boards/

[dcooke570]

Re: TM-0915 transformer

0.893 K ohms at secondary pins 1&2.
0.897 K ohms at secondary pins 3&4.

Same for the 2 blue caps near pins 1&4

http://t.co/gbXoWzO