Dell P1110 21" CRT repair thread

[Th3_uN1Qu3]

Re: Dell P1110 21" CRT repair thread

Been a while but i still have the monitor on my desk, have stripped the P1130 for parts since (screen was badly scratched). I'll dig up the mod tomorrow.

[CRockT]

Re: Dell P1110 21" CRT repair thread

Long time bump!!!

So, connecting the dots, i bypassed the drift correct thingy on the P1110. The brightness got significantly lower, i had to adjust G2 value with WinDAS again. The new G2 voltage for the P1110 was almost identical to the one the P1130 wanted. And... NO MORE BRIGHTNESS DRIFT!!!! I can finally have a proper monitor. Well, in fact, now i have two proper monitors.

How exactly did you bypass this? I am new to all this stuff, but did my first solder repair on a Trinitron TV recently; so I am ready to desolder some things off of this P1110 I got from CL a month ago, I just need to know what.

[Behemot]

Re: Dell P1110 21" CRT repair thread

Yes.
Breaking CRT monitors is considered first degree murder, so don't .

I do nothing to them, it just looks like they tend to have malfunctioning organs

[freaker]

Re: Dell P1110 21" CRT repair thread

I don't see it. This one by any chance?
https://www.badcaps.net/forum/showthread.php?t=14795


Nothing? No clicking or ticking either?
I'm not familiar with the P1110, but I suppose there should still be a clicking sound from the degauss coil relay when the monitor tries to start.

It's unlikely, but the power supply could be bad too. On my second GDM-FW900,the power supply would not come out of stanby *most* of the time (but occasionally it would and would work fine). I wonder if the Dell P1110 have the same issue, given how related these monitors seem to be.
To see if that's the issue, you would need a multimeter to check if the PSU gives the proper voltages when the monitor tries to start.

Well it might have made a sound for a moment. All torn a part until Wednesday when I will have time to do some testing.

It was mentioned that ADP Protect was too high a current coming from the flyback. Is there a way of testing the output?

During the course of checking out flybacks for a part I noticed that the Silcon Graphics seems to be a close match to the Sony CPD-E500

https://cdn.badcaps-static.com/pdfs/...f3f1c89374.pdf

[momaka]

Re: Dell P1110 21" CRT repair thread

Yes, that is the thread I was talking about.

Oh. Well, I already gave advice there. Not sure what else to suggest...
You don't have to be that gentle with CRT monitors. They can take quite a beating (though, it really shouldn't take any to open it).

Also, I just saw that you said that the base is attached to the back cover - in that case, you'll need to put the monitor face down to open it. There may also be latches on the side. Try prying with something thin like a big flat heat screw driver. Again, you don't need to be gentle (unless you really care about ruining that smooth beige finish on the monitor ).

Do you mind if I will bother you if something happenned to them?

Yes.
Breaking CRT monitors is considered first degree murder, so don't .

[lti]

Re: Dell P1110 21" CRT repair thread

I don't see it. This one by any chance?
https://www.badcaps.net/forum/showthread.php?t=14795

Yes, that is the thread I was talking about.

[Behemot]

Re: Dell P1110 21" CRT repair thread

Ohhhh, CRT lovers, I found paradise

I unfortunatelly had to brick sopme displays which died for me in the past years, amongst them was one 19'' Mitsubishi DiamondBack with totally perverse colors for its age. I will miss him Had bad caps, but was working like charm till it bricked completelly.

Anyway, now its cheap, I even got Phillips Brilliance 202P4 for free:-D Currently have this with Dell P1130 and one spare HP (but its big like house:-D).

Do you mind if I will bother you if something happenned to them? So far I only spilled juice over the Phillips once and had to change SMD switches on the front after few months (they died completelly), since than it works fine *pit-pat*

[momaka]

Re: Dell P1110 21" CRT repair thread

No, I am not kidding. Look at the thread I made about it.

I don't see it. This one by any chance?
https://www.badcaps.net/forum/showthread.php?t=14795

Doesn't make any sound.

Nothing? No clicking or ticking either?
I'm not familiar with the P1110, but I suppose there should still be a clicking sound from the degauss coil relay when the monitor tries to start.

It's unlikely, but the power supply could be bad too. On my second GDM-FW900,the power supply would not come out of stanby *most* of the time (but occasionally it would and would work fine). I wonder if the Dell P1110 have the same issue, given how related these monitors seem to be.
To see if that's the issue, you would need a multimeter to check if the PSU gives the proper voltages when the monitor tries to start.

[freaker]

Re: Dell P1110 21" CRT repair thread

Is there a screeching sound when that happens? If you look on the left side through the vents on the back of the CRT with the front of the CRT tube facing you, do you see any white-blue glow?
Reason I ask is because I looked at the schematic for the D-board, and it seems identical to what I have in my 24" GDM-FW900. I hope you don't have the same problem as I wasn't able to fix mine yet, and it's starting to look more and more like the tube has leaked air.

Doesn't make any sound. But I know the pressure on the inside of the tube is the same as the outside. If it wasn't when it happened it is now. [edit: Ok maybe not. It was just the anode cap and not actually the vacuumed space of the tube. ]

[lti]

Re: Dell P1110 21" CRT repair thread

You're kidding, right? CRT monitors are a piece of cake. Moreover, none of them require prying like LCD monitors.

No, I am not kidding. Look at the thread I made about it.

[momaka]

Re: Dell P1110 21" CRT repair thread

If either port is connected and the switch is not set to that port I get the same result. However if I switch to that port it will sound like it powers up the tube. The lights goes green then immediately, 1 sec, turns orange and blinks every 2 seconds. Off for 2 seconds and on for less than a second. {edit: According to spec it would appear to be ABL protector}

Is there a screeching sound when that happens? If you look on the left side through the vents on the back of the CRT with the front of the CRT tube facing you, do you see any white-blue glow?
Reason I ask is because I looked at the schematic for the D-board, and it seems identical to what I have in my 24" GDM-FW900. I hope you don't have the same problem as I wasn't able to fix mine yet, and it's starting to look more and more like the tube has leaked air.

[freaker]

Re: Dell P1110 21" CRT repair thread

ABL protection tripping means high voltage is too high. Usually a sign of a bad flyback.

Thanks, I'll see what I can google up. Sounds like it is beyond my electrical abilities. But who knows, maybe I can find a fix like I did here at badcaps for an old broken LCD controller.

[Th3_uN1Qu3]

Re: Dell P1110 21" CRT repair thread

ABL protection tripping means high voltage is too high. Usually a sign of a bad flyback.

[freaker]

Re: Dell P1110 21" CRT repair thread

Does the heater still glow when it turns off? Or does the whole monitor go into standby?

I do not see anything glowing with the cover off.

With nothing connected and powered on, the green light comes on solid for a minute or two. Then it switches to a solid but dim orange.

If either port is connected and the switch is not set to that port I get the same result. However if I switch to that port it will sound like it powers up the tube. The lights goes green then immediately, 1 sec, turns orange and blinks every 2 seconds. Off for 2 seconds and on for less than a second. {edit: According to spec it would appear to be ABL protector}

[momaka]

Re: Dell P1110 21" CRT repair thread

Everything that should be connected to ground is connected to ground, so there is no such circuit in there.

Good to know. At the time I saw this monitor on Craigslist, there were some listings for a few other big monitors, most of them much newer. But I chose this one on purpose. It seems that these old non-flat Sony's are built a little better than the newer ones.

Here you go: http://www.eserviceinfo.com/download...ell_p1110.html

Thanks. I downloaded it but still haven't looked at it.

Check G2 voltage as per your service manual. Probe before the resistor that feeds it to the tube (otherwise the impedance of your multimeter will have an effect and the reading will be inaccurate).

Thanks for the suggestion. I'll probably do that after I do a bit of prep-work on my 830D multimeter (the separation between the input terminals seems a bit close, so I think it would be wise to add some insulation first if I decide to measure such high voltages).

If the picture is otherwise correct (no color issues, no trailing shadows or things like that), i'm guessing aged tube though.

None as far as I can tell. Like I said, the color is good, but just not as good as some of my other CRT monitors. What particularly bothers me is the brightness - I can turn it up, but only the dark colors become brighter. The whites stay almost the same (but IMO they should be a little brighter). Other than that, I really like it.

I never figured out how to get the cover off.

You're kidding, right? CRT monitors are a piece of cake. Moreover, none of them require prying like LCD monitors.

[lti]

Re: Dell P1110 21" CRT repair thread

Anyway, there you go. If you ever see one of those, now you know how to fix it. IIRC lti had a Sony Trinitron with the same brightness drift issue, get to work already man!

I never figured out how to get the cover off.

[Th3_uN1Qu3]

Re: Dell P1110 21" CRT repair thread

I went through and cleaned up the inside. Old tarnished thick dust and visually checked for pad components but nothing evident. Looks almost new now except for the side effect of not power up the tube.

Does the heater still glow when it turns off? Or does the whole monitor go into standby?

Very interesting find, Th3_uN1Qu3!
Since I have some Sony CRT monitors as well, I decided to check the schematics of their A-boards and here's what I found:
My 21" 1998-built Dell D1626HT doesn't even have a cutoff AMP IC for the RGB. Instead, it has a separate transistor/op-amp circuit for each. So I'm not sure if this incorporates such a drift correction circuit. See lower-right corner of attached picture.

Everything that should be connected to ground is connected to ground, so there is no such circuit in there.

I think I will grab me a copy of the P1110 schematic.

Here you go: http://www.eserviceinfo.com/download...ell_p1110.html

By the way, my D1626HT has good colors, but the contrast seems a little weak - that is, if I want bright whites, I have to turn up the brightness. But then the blacks become washed out. And if I turn down the brightness so I get nice deep blacks, then my whites are a bit dull. My contrast and color bias/gain are turned all the way up. Does this sound like a G2 issue? Or old tube, perhaps? I have somewhat corrected this issue by turning up the gamma through software. Colors are still not as vibrant as my older 17" Dell D1025HTX, though.

Check G2 voltage as per your service manual. Probe before the resistor that feeds it to the tube (otherwise the impedance of your multimeter will have an effect and the reading will be inaccurate).

If the picture is otherwise correct (no color issues, no trailing shadows or things like that), i'm guessing aged tube though.

Btw, i'm currently developing a method of thermal compensation involving the CRT itself - my P1110 still takes 15-20 minutes to warm up and 30 minutes to fully settle, and this is entirely due to the thermal dependence of the tube. The method i've devised should allow for <5 minutes warmup time, and uses a minimum amount of parts. It will control G2 voltage based on tube temperature, and will be done with a NTC thermistor placed on the tube neck and either a small micro (easier to set up) or just a couple trimpots (simpler, but takes a longer amount of time to tweak). I'm partial to the microcontroller solution, i have a couple PIC12F675s lying around doing nothing, and it's easier to touch up, as the percent of brightness drift over temperature will vary with the age of the tube.

[momaka]

Re: Dell P1110 21" CRT repair thread

Very interesting find, Th3_uN1Qu3!
Since I have some Sony CRT monitors as well, I decided to check the schematics of their A-boards and here's what I found:
My 21" 1998-built Dell D1626HT doesn't even have a cutoff AMP IC for the RGB. Instead, it has a separate transistor/op-amp circuit for each. So I'm not sure if this incorporates such a drift correction circuit. See lower-right corner of attached picture.
On the other hand, the Sony GDM-FW900, does have this drift correction circuit. In fact, the cuttoff AMP is the same as yours. Heck, even that portion of the schematic you posted is exactly the same as the FW900's - same part numbers at the exact same locations with the exact same board numbers. I think I will grab me a copy of the P1110 schematic. I still need to find a flyback for that other GDM-FW900. I doubt the P1110 will be compatible, but I'm still curious to see how much in common they have. Last month I saw 2 of these P1110 CRT monitors on Craigslist here.

By the way, my D1626HT has good colors, but the contrast seems a little weak - that is, if I want bright whites, I have to turn up the brightness. But then the blacks become washed out. And if I turn down the brightness so I get nice deep blacks, then my whites are a bit dull. My contrast and color bias/gain are turned all the way up. Does this sound like a G2 issue? Or old tube, perhaps? I have somewhat corrected this issue by turning up the gamma through software. Colors are still not as vibrant as my older 17" Dell D1025HTX, though.

[freaker]

Re: Dell P1110 21" CRT repair thread

Anyone have a clue as to what is occurring when a P1110 immediately shuts off after a few seconds regardless of which input is used. Prior to completely not powering up, I could flip the switch from the input it was connected to over at power up and flip it back after a few seconds and it would power up.

I went through and cleaned up the inside. Old tarnished thick dust and visually checked for pad components but nothing evident. Looks almost new now except for the side effect of not power up the tube.

[FIXITNOW]

Re: Dell P1110 21" CRT repair thread

good job