Can any One tell me how make this cap

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • sam_sam_sam
    Badcaps Legend
    • Jul 2011
    • 6018
    • USA

    #1

    Can any One tell me how make this cap

    Here ar some scan of this cap can any one tell me who make them and if are good to use in LCD monitors and TVs

    Thanks to any one that can help
    Attached Files
    Last edited by sam_sam_sam; 07-10-2011, 12:28 PM.
  • cadillacman
    Badcaps Veteran
    • Feb 2011
    • 524

    #2
    Re: Can any One tell me how make this cap

    105 deree rating- good. 1000 uf, yes i see that alot. 25v.. yeah wouldd be better if these were 35v or 50v but i could still see some use..

    now wether they are any good any good and low esr, i reallyt dont have a clue. Never seen a cap with that brand designation on it before.

    Comment

    • sam_sam_sam
      Badcaps Legend
      • Jul 2011
      • 6018
      • USA

      #3
      Re: Can any One tell me how make this cap

      This was in a box of caps that I got from Gold Mine Electronic for $6.00 there are brands in this box that I do know that are very good caps

      Is Union Carbite any good

      Comment

      • Th3_uN1Qu3
        Believe in
        • Jul 2010
        • 6031
        • Romania

        #4
        Re: Can any One tell me how make this cap

        I have the same brand of cap, but mine are 6800uF 35v (for a totally different application). On mine it says they're made in Japan... so they should be good.
        Originally posted by PeteS in CA
        Remember that by the time consequences of a short-sighted decision are experienced, the idiot who made the bad decision may have already been promoted or moved on to a better job at another company.
        A working TV? How boring!

        Comment

        • cadillacman
          Badcaps Veteran
          • Feb 2011
          • 524

          #5
          Re: Can any One tell me how make this cap

          heres a spec sheet. They call em low esr... looks like that series was intended for use in tvs/power supplies. Id run em.

          https://cdn.badcaps-static.com/pdfs/...39cf81347f.pdf

          Comment

          • sam_sam_sam
            Badcaps Legend
            • Jul 2011
            • 6018
            • USA

            #6
            Re: Can any One tell me how make this cap

            Thanks for the info I will use them I need some of these to recap a monitor

            Comment

            Related Topics

            Collapse

            • irepair559
              Ps4 1215a hdmi diode readings good everything good but no pic??
              by irepair559
              PS4 1215A HDMI DIODE READINGS GOOD EVERYTHING GOOD BUT NO PIC? everything is good! what else can it be? if hdmi diode values are good that means encoder and filters are good right? idk what else it can be guys...
              01-05-2023, 12:32 AM
            • Mgiffune
              Samsung UN60EH6000F Black Screen, Backlight and Sound Good. Power Cycle Returns Picture
              by Mgiffune
              I have a 60 inch Samsung UN60EH6000F flatscreen TV. The screen went black a few months ago Sound is good, backlight is good, no menu. I replaced the TCon board with a used board purchased from Ebay. It worked fine for a 3-4 months, then the screen started β€˜fading' back. Once again, sound is good, backlight is good, no menu. However, this time the picture looks fine for about 10-15 minutes, then fades back. If I power cycle the TV, the display reappears, for another 10-15 minutes, then fades black again. Repeatable ever time.

              I ordered a supposedly β€˜new' Tcon board this time, and
              ...
              06-09-2024, 10:28 AM
            • the_rem
              Unknown transformer : how to find a good replacement part ?
              by the_rem
              Hello guys,

              I would like a quite old but still good 800 W ATX PSU to be repaired. The problem was an extremely heavy coil whine coming from the small secondary transfomer on the PCB.

              I desoldered it hoping the references on the upper side would allow me to find a adequate replacement part. Sadly the written references drove me nowhere but to the manufacturer (I-MAG). I sent them a message like a bottle in the see asking them to send me a datasheet of the transformer. And... They responded ! I received a kind of datasheet (see attachment) but my competencies do not allow...
              04-23-2025, 01:48 AM
            • cook
              Good brands of run capacitor for house heat hump
              by cook
              Are there good brands for 'run capacitors' or 'start capacitors' that are used on electric motors or heat pump compressors? ... r are the good capacitor brands for electronics (power supplies, laptops, motherboards, etc.) also the good brands for run capacitors?
              Yeah I know this might be a novice question, but I just wanted to be sure. I did do a search on the forum but did not see this question asked before.

              Thanks
              09-13-2024, 12:53 PM
            • spleenharvester
              Good power bank shells for 18650 cells?
              by spleenharvester
              I did a cell salvage run on some Dyson batteries to build out a new fleet of Milwaukee batteries and the yield was a lot higher than expected, so I now have a lot of extra Sony VTC4s that are in reasonably good health. I'd like to build them into power banks, there's a glut of shells for 18650s on AliExpress but I don't know which are any good (read: won't explode). Can anyone recommend some (especially the ones that just fit a single cell)? Weld or weldless are fine, I have a spot welder

              I suppose USB-PD and/or quick charge would be desirable too

              Cheers
              05-11-2025, 01:47 PM
            • Loading...
            • No more items.
            Working...