HP w20. Total Shutdown. Cannot turn-on immediately.
Collapse
X
-
Re: HP w20. Total Shutdown. Cannot turn-on immediately.
Using my new DMM (beeper mode), i have traced the voltage source of Pin 1 of IC102 to be linked to the Emitter of Photocoupler (EL817).. I will try to check for voltages on that area & its respective components. Any other things to check?Comment
-
Re: HP w20. Total Shutdown. Cannot turn-on immediately.
ok guys,, hopefully this is the last time i am going to update this thread..
I just realized this. That the monitor, when plugged to Main Power, will be automatically start-up without me having to pressed the Power switch. Because i did remember switching it off (power switch) the last time i packed it up before continuing it again to troubleshoot just now.
Anyway, further tracing using the DMM, shows that IC103 (emitter pin) is also linked to Pin 1 of IC102. See attached. I continued to measure the voltage on the pins of both the photocoupler with respect to the -ve pin of the big cap. I measure it during stable on & when on standby (power plugged but monitor is not responding to Power switch - No Power LED on).
[IC pin> Stable On > Standby (coma)]
IC105
Pin 1 (Anode)> 121V > 121V
Pin 2 (Cathode)> 121V > 121V
Pin 3 (Emitter)> 0V > 0.72V
Pin 4 (Collector)> 16.5 > 13V (slowly decreasing)
IC103
Pin 1 (Anode)> 121V > 121V
Pin 2 (Cathode)> 121V > 118V
Pin 3 (Emitter)> 6.4V > 0.72V
Pin 4 (Collector)> 16.7 > 13.6V (slowly decreasing)
I thought it is strange that the Pin 3 of IC105 is having different voltage comparing with IC103. So i decided to swapped the 2 photocouplers.
Now when i first plugged to Main power, the monitor did not auto-start as it previously did. Power led is off. When I measure the voltage again, Pin 1 of IC102 is receiving 5.8V & Pin 3 (Emitter) of IC103 is now 6.63V..... But Pin 3 (Emitter) of IC105 is still 0V at standby.
I pressed the power switch, it light up & monitor is working as normal. I pressed it off and on again & it RESPONDED. Now i am leaving it plugged to the main Power overnight. Let's hope tomorrow it will wake-up when i pressed the Power switch,..
If it does wake-up, my DEEPEST APPRECIATION & GRATITUDE to those who contribute to this thread.. especially jetadm123 & PlainBill .. thanks for all the patience & guidance rendered in helping me to solve this from 9000+ MILES away....
.. Even though, I could not find the source of the problem but hope this thead will be useful for those with similar problem as well..
If not, then you will be hearing me again in the next few days....
Last edited by newbie1; 11-14-2010, 10:20 AM.Comment
-
Re: HP w20. Total Shutdown. Cannot turn-on immediately.
Since all you did was swap the photocouplers with each other and now have a working monitor, then the problem may have been a bad solder joint, which this model monitor seems to have a problem with.Comment
-
Re: HP w20. Total Shutdown. Cannot turn-on immediately.
Just to update, so far it is working (stable). I am typing this using it and it no longer shutting down/coma. It is also responding to the power switch well. Just that there are a few scratches here and there..
Anyway, thanks for helping me out, dude....
Comment
-
Re: HP w20. Total Shutdown. Cannot turn-on immediately.
thanks man.. i think its gonna stay with my boys for long while.. their gaming time is much much longer than i took trouble shooting this.. not to mention each of them wanting their own terminals.. kids nowadays.. spending lesser time at playground, football, soccer, basketball,etc.. Sigh!..Comment
Related Topics
Collapse
-
by bembenothe laptop works good but it turnon automaticaly after shutdown i replaced the windows and tried to replace the cmos battery i also updated the Bios but still the same
-
by cruiser_hi there,
Got this macbook after liquid damage. Nothing major, cleaned and reflowed what was suspect. Now, the laptop turns on and boots up but shuts off intermittently - sometimes after a few minutes, sometimes after a few hours.
Can be immediately started from keyboard right after. Plug stays orange during this time. No battery.
Gives shutdown cause -128.
Seem to work fine in SMC bypass.
Same shutdown happens with disconnected TP/KB/KBLED/CAM.
Observations:
- SMC_RESET_L - when pulled down - plug goes orange/green and... -
by howardc64History
- Got TV free. Prior owner claims Vizio logo shows up then nothing. He found U202 EEPROM replacement info (I know NickTV says its never EEPROM haha). Lifted 5 pads removing U202 without proper tools and thought thats end of main board. Gave the TV to me.
- I repaired U202 pads and connections. Soldered on prior owner purchased aftermarket EEPROM (original EEPROM was tossed). TV boots to VIZIO logo, then goes blank, shutsdown after a min or so and power on light blinks a number of times.
- Fixed 2 circa 2015 Vizios before with classical main board... -
hp fpw50-la-h323p rev 1.0
automatic shutdown after 30 sec of display coming
do not shutdown without ramstick
someone give me idea plz08-20-2024, 03:50 AM -
Hello Guys,
i think it is hard to find the GL752VW Rev2.1 schematic and boardview ! I have the same problème like "heso64", i don't know if he had resolved the issue at this time.
My Laptop was in standby and when I wanted to turn it back "on" by pressing a key it was "off". By pressing the "Power" button it did not turn back on and when I removed the plug from the power connector then reconnected -> it turns on with only 3 lights (Power, CAPS LOCK and Airplane mode) and no screen display or BIOS.
I searched and I can't find...-
Channel: Schematic Requests ONLY!
07-19-2024, 11:41 AM -
- Loading...
- No more items.
Comment