One little red line

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • bigbeark
    Badcaps Veteran
    • Jan 2010
    • 661
    • Canada

    #1

    One little red line

    I just purchased an Optiquest Q19WB 19 inch widescreen monitor at a really low price.

    Everything works fine, but after I did an Ubuntu update and restarted a tiny red vertical line appeared on the black Ubuntu flash screen.

    Most of the time, the line is invisible, against a white background it does not show at all.
    Given that the monitor was cheap and otherwise works fine, I am not too aggrieved.

    For future reference, what causes this, will it get worse, and is it fixable?
  • digge
    Badcaps Veteran
    • Apr 2006
    • 296

    #2
    Re: One little red line

    Ive seen it before, sometimes it can be as easy as just gently pushing a little at each end of the line, on the frame of the screen and it goes away. Dont press hard though cause that might make it worse. Think it was a laptop last time, think the owner clamped his hand together too hard on the edge and made it happen.

    Can be other things as well of course but start with the simple things.

    Comment

    Related Topics

    Collapse

    • cubytus
      Samsung UN50TU8000FXZC shows thin horizontal green line when warm
      by cubytus
      Hi to all,

      I was given this TV, an entry-level 4K 50" set. Some have criticized its lack of contrast and relatively poor colour rendering, but for my needs, it's very decent.

      I reset everything to factory settings, but this line keeps on fading in and out when watching a streaming channel from the Tizen firmware. Interestingly, it only happens when TV is warm, after about 1h45 of it being turned on.

      Watching a movie from an external source doesn't trigger the line as easily (needs 2 hours), and from a normal viewing distance, is hardly noticeable. It...
      01-10-2024, 01:26 AM
    • TrueSword88
      Kogan - KALED65XU9220STB - Blue Vertical Line
      by TrueSword88
      Hi all.

      I have a Kogan 65' LCD Panel with a thin blue vertical line (top to bottom) on left hand side of panel.
      The line just happens to coincide with the end of COF and start of the next COF (attached).

      The line is permanent no matter what I've tried. I've tried pressure testing the panel (top to bottom) and all over, I didn't notice any difference with the line, either temporary or semi-permanent.

      Also tried unplugging all flex cables, cleaned with isopropyl then re-inserting to no avail - line remains.


      Hoping to fix...
      05-05-2023, 04:28 PM
    • FALKLAN
      Running Line Voltage and Integrating LED Pods - Automotive
      by FALKLAN
      Howdy everyone! I hope all is well where ever you are!

      I'm attempting to integrate a couple of LED pods into an automotive reverse lamp circuit. The problem being, while the vehicle is running there is a 8.5v current present on the reverse lamp power wire. Needless to say is that all LED pods and lights dimly illuminate while the 8.5v is present, so the LEDs are always powered on while the vehicle is running. When the vehicle is shifted into reverse, the voltage changes to 12 volts.

      I am uncertain how to convert this line into a switched 12v output line for the LED pods....
      02-05-2025, 12:30 AM
    • mindoverflow
      ASUS GTX 1650 Gpu.Initialize Interrupt request line stuck asserted
      by mindoverflow
      hello,

      there is an asus gtx1650 which displays fine in windows but if i run a benchmark test it displays artifacts and the driver crashes after a second or two.

      I changed pads and thermal paste.

      I run mats test but it is reporting 0 errors.

      I then tried to run the mods version 400.271_1650 test, it first ran and stopped with a 'breakpoints limit reached after 5 retries' error and the fans went full speed.

      After a reboot, I tried to run the test again, but now the test fails and says "ERROR: Couldn't clear GPU's interrupt...
      02-09-2022, 03:22 PM
    • Technomancer
      Nintendo 2DS SD Card Reader issue. Problem on the clock line?
      by Technomancer
      I have a 2DS that I am working on that has a problem reading SD cards. It knows that card is in the slot (which, means the detect pin is working anyway) but it says it can’t read the card.

      Here is what I have done so far:
      -Tried SD card in another 2DS and on PC, works great.
      -Tried piggybacking another SD card slot (just so I didn’t have to take the other one off), same issue.
      -Compared voltage drop readings from a working 2DS to the faulty one. All reads are very close except one, the 7th pin from the left, with the pins closest to you, which I believe...
      06-07-2022, 09:01 PM
    • Loading...
    • No more items.
    Working...