Sae R-102

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mbates14
    Senior Member
    • May 2005
    • 169

    #1

    Sae R-102

    Anyone have a schematic for an SAE R-102 receiver? i have one that someone mucked up the tuner section and a couple resistors burned, transistors shorted that dont look like the right ones, etc....
  • Agent24
    I see dead caps
    • Oct 2007
    • 4951
    • New Zealand

    #2
    Re: Sae R-102

    Have you tried any schematics websites?
    "Tantalum for the brave, Solid Aluminium for the wise, Wet Electrolytic for the adventurous"
    -David VanHorn

    Comment

    Related Topics

    Collapse

    • SluggerB
      Help diagnosing Pyle Receiver PTA66BT with burned resistors
      by SluggerB
      Spoiler alert: I am a total noob at this, just getting into the hobby

      My buddy has an audio receiver that stopped worked, everything turns on and functions but no sound comes out of any output (Speaker, AV, or Headphone) So I said I would take a look at it. I popped the cover off, and saw an obvious issue: One of the resistors on the board had burned up.

      Photos:
      ...
      08-03-2020, 07:50 PM
    • mikey5791
      Need help to replace burned resistor in 350w atx psu
      by mikey5791
      Hi to all forum members,

      Got this faulty 350 watt atx psu dirt cheap from a local online seller as i am keen to use it as a learning tool to repair faulty power supply.
      The faulty part is quite obvious from the burn area near the 16pin KA7500 BD pwm. The fuse is still intact with good continuity.

      Upon power on ac, there is 5vdc standby power on cathode of diode D14 and about 10vdc on cathode of diode D13.(This should be the aux power to generate the 12v and 5v rail.)
      Initially i replace the two burned resistors near my marked red arrow to 200 ohm resistor...
      12-26-2024, 04:55 AM
    • DXseekerMO
      Samsung PN51F8500AFXZA broke off the tuner's F connector, can't get tuner de-soldered
      by DXseekerMO
      I can hear Fred Sanford now...."YOU BIG DUMMY".....I pulled the "F" connector out of the tuner by accident. The tuner number is BN40-00248B. Low and behold I had a scrap board with tuner number BN40-00248A. Although the tuner is different (according to Encompass.com) it's footprint on the board is exactly the same as the 248B so I decided to de-solder the tuner off the scrap board to see what I was getting in to.

      As you can see in the picture the terminals and solder pads are super small. No matter what I tried I could not get either the terminals or support...
      09-15-2021, 05:15 PM
    • wolf1976
      wireless receiver for 6 speeds fan control with remote control
      by wolf1976
      hi i have a receiver that is destroyed from the overvoltage i guess
      my question is has three wires u v w for driving a motor fan i found an other receiver wireless from aliexpresss with the same propertiew but for dc motor
      the motor fan has not label
      i have an other receiver operational
      In your opinion can i measure the voltage at the output ?
      what do you suggest me with a simple instrument multimeter or using someone instrument more specific ?
      thanks in advance...
      07-23-2025, 03:12 PM
    • CdDvdFlash
      DSE GE6878 possible TV receiver dying remote not working well
      by CdDvdFlash
      For this Dick Smith TV GE6878 (Thompson) I replaced the broken remote with a universal it kinda works though if its more than a few meters away sometimes the buttons register and sometimes they wont so I bought another remote from another brand and it has the same problem, I've had an old TV in the past that the sensor died completely and I replaced it to fix it could this be a similar problem? I tried looking for a service manual, spare parts for a receiver and a parts list but I couldnt find any info. can someone please help me to find the info online for a service manual or where I can buy...
      07-03-2024, 03:55 AM
    • Loading...
    • No more items.
    Working...