Yamaha RX-V371 No Power, HDMI Problem

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • mosscomes
    New Member
    • Oct 2016
    • 2
    • USA

    #1

    Yamaha RX-V371 No Power, HDMI Problem

    I've got a suddenly dead Yamaha RX-V371. A few weeks ago, there was a considerable delay in switching between HDMI sources (black TV screen, sometimes a "no signal error." Then it just shut down.

    Now, there's no power, hitting the on-off button does nothing. I get one click when I hold the on-off and reset buttons, but no power nor flicker from the LED's.

    The Fuse is OK. Power out from the Operation PCB seems ok. I tested transformer and that seems to be ok (no Thermal Fuse issue).

    The power problem with these models seems to be common, but I've not
    found anything on the HDMI switching issue, which may be where it all started.

    Any ideas?
  • budm
    Badcaps Legend
    • Feb 2010
    • 40746
    • USA

    #2
    Re: Yamaha RX-V371 No Power, HDMI Problem

    Service manual:
    Never stop learning
    Basic LCD TV and Monitor troubleshooting guides.
    http://www.badcaps.net/forum/showthr...956#post305956

    Voltage Regulator (LDO) testing:
    http://www.badcaps.net/forum/showthr...999#post300999

    Inverter testing using old CFL:
    http://www.badcaps.net/forum/showthr...er+testing+cfl

    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
    http://s807.photobucket.com/user/budm/library/

    TV Factory reset codes listing:
    http://www.badcaps.net/forum/showthread.php?t=24809

    Comment

    • bigfins64
      New Member
      • May 2016
      • 1
      • Australia

      #3
      Re: Yamaha RX-V371 No Power, HDMI Problem

      Originally posted by mosscomes
      I've got a suddenly dead Yamaha RX-V371. A few weeks ago, there was a considerable delay in switching between HDMI sources (black TV screen, sometimes a "no signal error." Then it just shut down.

      Now, there's no power, hitting the on-off button does nothing. I get one click when I hold the on-off and reset buttons, but no power nor flicker from the LED's.

      The Fuse is OK. Power out from the Operation PCB seems ok. I tested transformer and that seems to be ok (no Thermal Fuse issue).

      The power problem with these models seems to be common, but I've not
      found anything on the HDMI switching issue, which may be where it all started.

      Any ideas?
      HI Did you have any luck finding a solution to this . I have two of these units showing similar symptoms . I have narrowed it down to being a problem on the hdmi board , which is also the main control board and yes the hdmi issues seem to progress into no display (which most people think means no power ) I have spent a bit of time checking voltages on the board and everything seems ok . at this stage I can't justify spending any more time tracking the fault but it does seem very common from the brief searches I have done so maybe someone has spent the time .

      Comment

      Related Topics

      Collapse

      • theone111
        Problem with LG Plasma 60PM6700 - Random power downs
        by theone111
        I have an LG Plasma TV 60PM6700 for the past ~12 years.

        In the last ~3-4 months I have been having some issues.
        1. Problem: It started with random picture disappearing (sound still worked).
          Frequency: Happened about once a week.
          Solution: Had to turn off TV wait a few seconds before turning it on again.
        2. Problem: Then it got worse and the TV started to shut down and when turning on the no picture just sound.
          Frequency: Happened about once a week.
          Solution: Had to turn off TV wait about 10-20 seconds and turn it on again to solve.
        3. Problem: TV shuts down
        ...
        07-22-2024, 10:36 AM
      • Duranitron
        Asus x512dk rev 2.1 power on problem
        by Duranitron
        When I reflash again the bios of hoaca388 the unit powers on and the unit lives!!! Hooray!! All voltage in the coil 3.3v, 5v and 6.7v indicate charging are all present. including the cpu voltage , EEPROM and GPU voltage the unit is now alive, normal screen booting to windows and log in screen until I power it off. Then the unit never goes on even when pressing the power button in the keyboard.. Voltage reading 19v main , 3.3v VCC in IT8225E-128 and EEPROM VCC 0 volt and the charging voltage 0 volt.

        Try to trace the power switch button goin to the power switch IC PU8803 (APL3533AQBI-TRG)...
        11-26-2024, 10:22 PM
      • Tynan Dill
        Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
        by Tynan Dill
        I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

        Upon bringing it home and plugging it up, it showed a standby light.

        I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

        The screen seems to blackout and stay black, but with a flashlight I can see the display.

        With my Playstation 4 connected via HDMI, and running a game I can hear sound.

        Assuming...
        11-22-2024, 01:46 PM
      • EazyBone
        LG OLED55C9PUA power problem
        by EazyBone
        Hello, trying to fix C9 55 inch. I have pulled the back and all looks completely normal with nothing burnt so far. This is first time attempting to fix a tv so any help is appreciated.

        Problem. I hit power button, red light on TV turns off and tries to turn on, no picture shows up and then shuts off. This occurred after house power turned on and off, not from a storm.

        I have tested the power going from power supply to main board, all 12v and 20 volt readings are proper when I hit power button.

        The power supply to t con is different story.
        This...
        06-23-2023, 07:43 AM
      • Dr.d
        Help please..Lenovo ideapad 5 14itl05 power and charging problem
        by Dr.d
        I have a lenovo ideapad 5 14itl05, board LA-K321P, That will only power up on Battery only, or with battery disconnected and power adapter only. If battery is connected and usb-c power plug connected. It only works on battery and will not charge. I can however force it to charge by connecting the battery from a disconnected state while the power USB c plug is powering the laptop.

        Additionally....to add to this strange situation. The usb-c power plug ONLY works to power the laptop on one side when inserted into the boards power usb c plug. If you rotate it 180 degrees, the board gets...
        04-05-2024, 11:48 AM
      • Loading...
      • No more items.
      Working...