i have some old components & a not so old boombox that hopefully are only suffering from crud/corrosion that can be cleaned & lubed to restore function.
the amp & turntable both have declined in function over the years & were put on a closet shelf for 5+ yrs. amp right channel was weak & now dead. tested phone, tape, aux & tuner inputs & left channel output is good on those components (R channel works fine in L input). speakers work fine on L output. i'll do all the knobs, but give attention to volume, pullout mix, and balance & hope that solves it like it did for ntehicks in his thread
https://www.badcaps.net/forum/showthread.php?t=27273
the turntable works but the speed control knob no longer raises the rpm up to spec. it may need to be re-adjusted after cleaning (i have the manual & instructions for V1 & V2 pot adjustment). here are links where i found good info & manuals (must register to download)
in the pic below you can see the boombox has a set of 4 push buttons on top the CD door - some intermittent, some not working - the round one next to them works fine. it was used in a workplace, so dust etc landed on it regularly. still have the remote which works fine.
i've not used contact cleaner or lube before, so hoping those who have will offer more specifics than what i've already read here or watched on youtube - namely:
1. product - i'm not in a hurry & willing to spend more for a better product, but if i can get something local that is pretty good, i'd at least like to be able to consider it. i found microcenter carries paired 0.5oz spray deoxit spray & gold (looks like i can get 10x as much for less than $10 more elsewhere), & lowes has 13.5oz spray IDEAL Contact Cleaner
2. application - spray or needle or brush or plastic tube. which deoxit (5% or 100%) & application method works best for various things i'm hoping to clean. do i need the spray to wash out the contacts, or can i let them soak a bit (how long - i read one suggestion of repeating over 2-3 days? does the cleaner dry quickly?), work the knob ~25 times and use canned air to blow out the crud (air is cheap!)
3. where & how to apply - the vids i watched showed pots that have a hole on the bottom side & said that if not accessible, trying to get some from the front past the knob post/stem (knobs just pull off or what?). for the turntable internal speed adjust pots with the screw slot on top - go thru the top or? how about the topside control knob, also pops off? for the boombox buttons, do they pop off, or shall i apply on the top edge & let gravity do the work? any worries about the little LCD screen below?
any advice is appreciated - thanks
the amp & turntable both have declined in function over the years & were put on a closet shelf for 5+ yrs. amp right channel was weak & now dead. tested phone, tape, aux & tuner inputs & left channel output is good on those components (R channel works fine in L input). speakers work fine on L output. i'll do all the knobs, but give attention to volume, pullout mix, and balance & hope that solves it like it did for ntehicks in his thread
https://www.badcaps.net/forum/showthread.php?t=27273
the turntable works but the speed control knob no longer raises the rpm up to spec. it may need to be re-adjusted after cleaning (i have the manual & instructions for V1 & V2 pot adjustment). here are links where i found good info & manuals (must register to download)
Code:
www.hifiengine.com/manual_library/fisher/ca-880.shtml www.vinylengine.com/library/akai/ap-d40.shtml
i've not used contact cleaner or lube before, so hoping those who have will offer more specifics than what i've already read here or watched on youtube - namely:
1. product - i'm not in a hurry & willing to spend more for a better product, but if i can get something local that is pretty good, i'd at least like to be able to consider it. i found microcenter carries paired 0.5oz spray deoxit spray & gold (looks like i can get 10x as much for less than $10 more elsewhere), & lowes has 13.5oz spray IDEAL Contact Cleaner
2. application - spray or needle or brush or plastic tube. which deoxit (5% or 100%) & application method works best for various things i'm hoping to clean. do i need the spray to wash out the contacts, or can i let them soak a bit (how long - i read one suggestion of repeating over 2-3 days? does the cleaner dry quickly?), work the knob ~25 times and use canned air to blow out the crud (air is cheap!)
3. where & how to apply - the vids i watched showed pots that have a hole on the bottom side & said that if not accessible, trying to get some from the front past the knob post/stem (knobs just pull off or what?). for the turntable internal speed adjust pots with the screw slot on top - go thru the top or? how about the topside control knob, also pops off? for the boombox buttons, do they pop off, or shall i apply on the top edge & let gravity do the work? any worries about the little LCD screen below?
any advice is appreciated - thanks
Attached Files
Comment