Re: CH341a SPI / I²C programmer
Hello
I have a program that is not register how to register
CH341a SPI / I²C programmer
Collapse
X
-
Re: CH341a SPI / I²C programmer
i dont have a "registered" one.
i cant hack it because it's compressed.
you can run it in trial mode but i dont think it works long like that.Leave a comment:
-
Re: CH341a SPI / I²C programmer
Could you share your 1.29 version, please.
Thanks.Leave a comment:
-
Re: CH341a SPI / I²C programmer
Thanks again for now i will just unsolder it a reprogramme etc its a one of project anyway for now i ussually just by a new main board but as this file was available i thought it was worth a try.Leave a comment:
-
Re: CH341a SPI / I²C programmer
probably not a good idea.
when you use those you have to stop the host system from trying to access the chip at the same time.
the other thing is chip width.
there are 2 sizes, narrow(150mil) and wide(200mil).
those clips are designed for the narrow chips usually like 24' series eeproms.
the 25' series flash chips are usually wide.
this may be more helpfull
http://www.ebay.co.uk/itm/271635665570Leave a comment:
-
Re: CH341a SPI / I²C programmer
Thanks again stj i will try that ive just saw these on ebay would saw me desoldering the chip whats your toughts on these?
http://www.ebay.co.uk/itm/1513318796...%3AMEBIDX%3AITLeave a comment:
-
Re: CH341a SPI / I²C programmer
read the old chip,
save the file.
unzip that archive and load the .bin file into the programmer.
then erase the chip (you cant program a chip unless it's blank)
then program the chip.Leave a comment:
-
Re: CH341a SPI / I²C programmer
this is the one i have downloaded cheers.Attached FilesLeave a comment:
-
Re: CH341a SPI / I²C programmer
firstly, you ALWAYS save a backup of the original data - incase you make things worse.
then you can atleast recover to where you started.
can you upload the file you want to write.Leave a comment:
-
Re: CH341a SPI / I²C programmer
Thanks for the info stj ive only brought the programmer to try to add the spftware to a eeprom on a technika tv/dvd combi i have a issue with freeview wont tune i have found the bin? file here http://www.tv.quuq.org/forum/index.php?topic=6012.0
stj do i read my old chip save the old file and then unzip the down load and add all the files? its the first time im trying to do this sort of thing anyadvice you can offer?
the set was a freebie so ideal for expermenting with.Leave a comment:
-
Re: CH341a SPI / I²C programmer
open the file "Config.ini"
change the language setting to say "language=1033"
the default path to open and save files is in there if you want to change it too.Leave a comment:
-
Re: CH341a SPI / I²C programmer
Can we change the language in these? like in the one in the youtube link.Leave a comment:
-
Re: CH341a SPI / I²C programmer
o.k. for anybody who owns one of these.
there are 2 windows drivers to install.
1: a virtual comport
2: a virtual parallel port and i²c driver
then there are 2 softwares.
1: the memory programmer
2: the AVR microcontroller programmer
now as far as the memory programmer goes, the versions upto 1.18 just work
versions from 1.20 onwards need to be registered.
and i have 1.18 and 1.29 if anybody needs them.
------------------------------------------------------------------
btw, the key to finding this stuff is simply to use a chinese search engine - it's like turning on the lights in a dark room!Leave a comment:
-
Re: CH341a SPI / I²C programmer
soooo.........
now i may have found version 1.26
http://www.vdisk.cn/down/index/13405566Leave a comment:
-
Re: CH341a SPI / I²C programmer
well i got that chinese Vdrive file down.
it's passworded: 13579
and contains 1.18 software + drivers + some type of atmel programmer.
also a big load of eeprom dumps and some documents.
Leave a comment:
-
-
-
Re: CH341a SPI / I²C programmer
not sure what software version it is how can i tell? (this is my one) http://www.ebay.co.uk/itm/2914383733...%3AMEBIDX%3AIT
i cant download this either have tried for you.
this ebay link has the download link for the software that does down load but says it has a virus? its in chiness though it may have what you want?
http://www.ebay.co.uk/itm/2216127633...%3AMEBIDX%3AITLast edited by vinceroger69; 06-24-2015, 02:12 AM.Leave a comment:
Related Topics
Collapse
-
by what_1282105Following this guide (https://www.reddit.com/r/thinkpad/co...g_and_flashing) i re-flashed my t480s BIOS using an external (CH341A) programmer. The flash didnt work, so i reverted back to my BIOS backup successfully. The BIOS in the chip and the BIOS backup file are identical according to windows' file compare. The revert, however, didnt work: the only thing the computer does is flash the power button 3 times when AC power is connected. I've tried unplugging the CMOS battery, holding the reset button and holding down the power button- no signs of life....
-
Channel: BIOS Requests ONLY!
-
-
My pc updated bios through Windows Update and I was greeted with BLACK SCREEN WITH CPU FAN MAX SPEED. I don't think there is even a screen signal, because it triggers my monitor for a couple seconds and then the monitor turns off. I tried the other outputs as well.
- I tried clearing bios, resetting bios, removed the CMOS battery, removed m.2 ssd, wifi, and ram. Still black screen with CPU fan blasting.
- I tried using the Lenovo BIOS CD and BIOS USB, but neither worked. At least I couldn't get anything to work.
- I could only locate two chips that look like bios chips. Could someone verify this
-
Channel: BIOS & Schematic Requests!
-
I'm able to read and write the chip by selecting a winbond IC of the same size, but when verifying it fails at around 25 percent.
I've modded the ch341a to 3.3v.
Can I update the database to include the XMC 25QH256C? -
by sasalliHi to all!
i have ch341a programmer. iam trying to program MX25L6475EM2I-10G chip with 16mb file, bu the programmer software(v1.18) says ''FILE LENGHT, BEYOND RANGE OR IT WILL BE IGNORED''. What should i do? Thanks! -
by fanchiottiHello everyone,
I have a lenovo ideapad s145-api and after a bad bios update, it's bricked.
I bought a ch341a programmer, installed all the drivers, it's working as expected, except when i put the clamp on the bios chip the power led goes dim and the win 10 emits the "device is disconnected" sound.
NeoProgrammer doesnt detect the chip at all...
The laptop battery is disconnected as is the bios battery.
I believe the bios chip is this one: https://www.winbond.com/hq/product/c...ory/serial-nor... - Loading...
- No more items.
Leave a comment: