How do I get rid of the burning smell?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Logistics
    Badcaps Veteran
    • Apr 2007
    • 721
    • USA

    #1

    How do I get rid of the burning smell?

    So my pre-amplifier took a dump, tonight. No apparent reason other than age, I suspect. It's a Yamaha C-65 preamp. I suspect the transformer itself may have taken a dump--I'll open it up, tomorrow to see if I find anything obvious, but I had to physically remove the unit from the house, and store it out in my car for the night because it stinks so bad. The remaining burning smell is stinking up the apartment, and I have one of those wives with the super sensitive noses, who smell every little thing so it's bugging the hell out of her.

    Is this smell gonna stick for a long time? Do I need to go at the whole house with some Lysol or other deodorizer? I've got fans blowing across the apartment, all the windows open, but it's lingering. I used some citrus cleaner around the area the preamp was sitting, hoping to remove any residue? I don't know.

    Ideas?

    Matthew

    p.s. This was the preamp I used for headphone listening, too! Waaah!
    Presonus Audiobox USB, Schiit Magni 3, Sony MDR-V700
  • Andrew F. Ali
    Badcaps Legend
    • Jan 2014
    • 2450
    • Trinidad & Tobago

    #2
    Re: How do I get rid of the burning smell?

    That burning smell could be from a ruptured capacitor in the power supply or anywhere in the circuit. Though too it could be a semi-conductor like rectifier diode, transistor or IC. It is only when you open it up and switch it ON in a controlled environment, then you may discover the source of the smell and the fault on the pre-amp.

    Comment

    • stj
      Great Sage 齊天大聖
      • Dec 2009
      • 30937
      • Albion

      #3
      Re: How do I get rid of the burning smell?

      it could be anything - even burned paxoline or cable insulation.
      get it open fast - the sooner it's open, the sooner you can blow out the smell and find the cause.

      Comment

      • Logistics
        Badcaps Veteran
        • Apr 2007
        • 721
        • USA

        #4
        Re: How do I get rid of the burning smell?

        This was what caused the smell, which seems to have subsided from the house, today. Although, I had a wooden crate sitting on top of the unit (there's no vents so it doesn't matter) and it seems to have absorbed the smell.
        Attached Files
        Presonus Audiobox USB, Schiit Magni 3, Sony MDR-V700

        Comment

        • Andrew F. Ali
          Badcaps Legend
          • Jan 2014
          • 2450
          • Trinidad & Tobago

          #5
          Re: How do I get rid of the burning smell?

          Those two transistors probably shorted out burning the resistors and PCB. I am almost certain the copper traces were burnt as well. Can be repaired but will take some time and patience.

          Comment

          • kc8adu
            Super Moderator
            • Nov 2003
            • 8832
            • U.S.A!

            #6
            Re: How do I get rid of the burning smell?

            that has been cooking a long time.
            looks like a design flaw that finally caught up to it.

            Comment

            Related Topics

            Collapse

            • howardc64
              LG 65UQ8000AUB no backlight burning smell
              by howardc64
              Only 3 years old. Owner said backlight went out and burning smell. Didn't bother plugging in to check if had power LED. Just opened the TV rear and found shorted bridge rectifier diode on the backlight circuit on the PSU. SF26G (400V 2A super fast recovery rectifier link ) diode replace with SF26 (what I had on hand) Google AI said G = Green Components.

              Burn looked pretty bad on the board but just was blackened carbon coating material. Scraped and cleaned off quite well and clean solder pad for the new diode.


              ...
              06-07-2025, 10:38 PM
            • sew333
              Can i plug pc on this apartment with older fuse box?
              by sew333
              Hello. I will be buying new apartment to live. But fuse box is older. Not the newest.

              And my question. It will be fine to plug pc in this new apartment with that fuse box,i think it is aluminium,right?

              PC WILL BE: Rtx 4090,14900K,1600W PSU

              It looks like this ( screen from internet ). Looks like this,not sure i dont take a pic from there. Can i plug pc with that one?

              screen of this:


              room:




              Someone said this to me.

              1

              "I would get advice from a local electrician...
              03-29-2024, 05:37 PM
            • stormanimal83
              Gigabyte B450 Aorus Pro stuck at VGA LED, burning hot LED Controller MCU 1 under PCI slot...
              by stormanimal83
              Hey....

              Board as written in description was stuck at VGA LED. common Problem wit these type of bords.... tried all the "standard stuff" like resettin... reseatin.... found out the LED Controller MCU1 = IT8295FN-56A geting burning hot under the last PCI Slot.. now i desoldered it cause there were only 18 ohms at the caps arround.... another aorus x470 in working condition with similar part and nearly same layout had arround 280 ohms...

              my question is: why doesnt the board start know without this chip.... worked myself through the boardview but i can´t understand...
              01-18-2024, 02:15 PM
            • ignacio.ino27
              Vaio DA0HK1MB6E0 MBX-247 Burning any EC
              by ignacio.ino27
              Hello to all.

              I have this Sony Vaio QUANTA HK1 DA0HK1MB6E0 MBX-247 that is burning the NUVOTON EC when you connect it to power supply.

              1) The +3vpcu line is going to a direct short after connecting the motherboard to power supply.
              2) I discovered the EC NUVOTON was shorted. After removing it the short gone out on that line (+3vpcu) but... (If i quit the EC the 3.3v are pressent on +3vpcu because the shorted component was quited)
              3) There were no shorts after soldering the new EC NUVOTON. But after connecting the board to power supply the EC keeps burning...
              05-07-2022, 05:24 PM
            • androw ezzat
              HP ZR22W burning mode
              by androw ezzat
              hallo i have HP ZR22W

              ​ have burning mode the screen flicker bule.green.whit .red
              05-03-2025, 03:01 PM
            • Loading...
            • No more items.
            Working...