Bad cap or not ?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • naughtycap
    New Member
    • Jun 2017
    • 5
    • poland
    #1

    Bad cap or not ?

    Hi

    Here is a capacitor inside a faulty Moog MF-104Z delay pedal. What do you think ?

    I -might- have fed the unit 15 volts instead of 9v....
    Attached Files
    Tags: None
    • stj
      Great Sage 齊天大聖
      • Dec 2009
      • 31015
      • Albion
      #2
      Re: Bad cap or not ?

      what does it say on the other side?

        Comment

        • naughtycap
          New Member
          • Jun 2017
          • 5
          • poland
          #3
          Re: Bad cap or not ?

          here's a pic :
          Attached Files

            Comment

            • stj
              Great Sage 齊天大聖
              • Dec 2009
              • 31015
              • Albion
              #4
              Re: Bad cap or not ?

              so why the concern, it's rated upto 50v

                Comment

                • naughtycap
                  New Member
                  • Jun 2017
                  • 5
                  • poland
                  #5
                  Re: Bad cap or not ?

                  allright
                  thanks !

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • CG2
                      Janome DC3050 Sewing Machine Pedal Resistance
                      by CG2
                      OK, this is a long shot. I got this sewing machine cheap because it's end of line, ex-display, and had no pedal. The genuine pedal costs £60, while Ebay knock-offs go for around £15. So I went for the knock-off, it doesn't work, and I'm not sure whether it's the pedal or the sewing machine that has the problem.

                      Now this is an electronic machine, unlike the old fashioned sort where the pedal was a big resistor in series with the power to the motor. Here, the pedal is just (I think) a variable resistor fed with a 5 volt supply, and limited to a current of 5 milliamps. Assuming that...
                      04-14-2023, 07:53 AM
                    • MisterAIL
                      PS5 digital / No Power / No Beep / Good power supply
                      by MisterAIL
                      Hi everyone,

                      Brought a non functionnal PS5. Apparently only a bad PSU...
                      No beep, nothing.

                      After some tests i found this :
                      - PSU is fine (12 volts stable)
                      - 12 volts line is shorted
                      - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
                      - By the way, nothing change. No signal, no power, no beep.

                      Mesuring all rails with my workbench psu (12 volts input)
                      - 0.00 amp drawing
                      - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
                      3.3v PMIC
                      5 Photos
                      03-12-2024, 03:24 PM
                    • Mcfeetroy
                      Fishing bite alarm drains battery
                      by Mcfeetroy
                      Good day to all. The bite alarm drains 9-volt Krona batteries. Current consumption when switched on is about 50 mA. I wiped the board from oxides, I will attach a photo (on the board there is a j3y transistor and a 7533 stabilizer, the microcircuit is erased = (the 3.3-volt stabilizer heats up weakly. I replaced it, nothing changed. I unsoldered the microcircuit, the consumption disappeared. The resistance on the pins of the unsoldered microcircuit from the point clockwise is more than 2 megaohms, the 11th leg is presumably ground. I warmed up the microcircuit, the consumption does not change....
                      Yesterday, 03:52 AM
                    • BTubbs200
                      Dead Dell Latitude 5420 not receiving 20 volts from USB-C charger
                      by BTubbs200
                      Hello,

                      Dell Latitude 5420 P137G
                      Board: LA-K491P REV A01

                      I have received this laptop which was described as "does not power on or accept charge." Battery shows no sign of charging when charger is plugged in, nor does the board show any signs of life when battery is unplugged and charger is plugged in. No light from the LED at all or any other indications of activity.

                      Board seems to have no shorts, all power rails are fine and show high resistance.

                      When charger is plugged in, voltage is present in 3.3V rail but absent in others....
                      01-24-2025, 08:15 PM
                    • sam_sam_sam
                      MPJA 10 AMP @ 0 to 30 Volts Switching Power Supply Cap Fault
                      by sam_sam_sam
                      I have this 10 amp 0 to 30 volt switching power supply that decided to have a 630 milliamperes draw on it at 0 volts

                      I open it up to find non brands name capacitors in it

                      I am not sure how this switching power supply is set up

                      Could someone please explain how this power supply works

                      Here is the capacitor ESR results

                      (1) 47uf@50 volts 0.46
                      (2) 47uf@50 volts 0.45
                      New 47uf@50 volts 0.35

                      (1) 100uf@25 volts 0.34
                      (2) 100uf@25 volts 0.35
                      New 120uf@50 volts 0.08

                      (1) 220@25 volts 0.13...
                      10-21-2018, 10:02 AM
                    • Loading...
                    • No more items.
                    Working...