Capacitors in series max ripple

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • TELVM
    Badcaps Veteran
    • Oct 2012
    • 547
    • Spain
    #1

    Capacitors in series max ripple

    Let's say I put two Nichicon HN, 1500uF, ESR=0.009, Max Ripple=2900, in parallel on the +12V rail of a PSU.

    Combination's capacitance will be 1500 +1500 = 3000uF

    Combination's ESR will be 0.009 / 2 = 0.0045

    What will be the combination's max ripple? Equal, higher or lower than the 2900 of a single cap?
    Last edited by TELVM; 08-12-2015, 06:29 AM.
    Tags: None
    • stj
      Great Sage 齊天大聖
      • Dec 2009
      • 31026
      • Albion
      #2
      Re: Capacitors in series max ripple

      ripple will double.

        Comment

        • TELVM
          Badcaps Veteran
          • Oct 2012
          • 547
          • Spain
          #3
          Re: Capacitors in series max ripple

          (Screwed up the title, I meant two caps in PARALLEL).

          So the combined max ripple of two caps in parallel of 2900 max ripple each will be 5800?

            Comment

            • SteveNielsen
              Retired Tech
              • Jun 2012
              • 2327
              • USA
              #4
              Re: Capacitors in series max ripple

              The combined (total) current through both caps in parallel will be double the current through only one of them because the effective resistance of the circuit has been cut in half while the voltage remains the same. I=E/R. If R is cut in half then R will go into E twice as many times, meaning that I doubles.

                Comment

                • TELVM
                  Badcaps Veteran
                  • Oct 2012
                  • 547
                  • Spain
                  #5
                  Re: Capacitors in series max ripple

                  Thanks!

                    Comment

                    Previous template Next

                    Related Topics

                    Collapse
                    • dragon3x
                      After updating motherboard capacitors, what to do next (Asrock K7VT2, SOLTEK SL-75FRN2L)
                      by dragon3x
                      Hi, I have some 32 bits computer motherboards that need repair, as they fail to
                      power on.

                      Here are some examples :

                      (N.B. "capacitors" indicated here are electrolytic capacitors located in the onboard
                      switching supply area).
                      (N.B. #2 : I could not find a 3300 microF aluminum-polymer with a higher voltage
                      than 6.3 V.)

                      1 - Motherboard #1 : this is an Asrock K7VT2 (socket A) that still works well. To put it on test
                      I replaced capacitors with aluminum-polymer.
                      3300 microF/6.3 V. x 4 replaced by 3300 microF/6.3 V. (KYOCERA...
                      03-21-2025, 02:46 PM
                    • sam_sam_sam
                      Panasonic switching power supply daughter board has two 27uf @ 50 volt capacitors which I do not keep in stock
                      by sam_sam_sam
                      I did not have any 27uf @ 50 volt capacitors but one nice thing is that it has enough room for two capacitors in parallel a 22uf and a 4.7uf @ 50 volts 22 plus 4.7 equals 26.7uf which so very close to 27uf I will show some pictures of it sometime tomorrow

                      This is one of the shit est boards I seen in a very long time and it was the daughter board the traces just lifting off the board I had to use the capacitor leads to repair the the traces and the main board is not any better because I had to repair several traces for the daughter board to the main board

                      After all of...
                      07-13-2024, 08:14 PM
                    • chth96
                      Is it no harm to replace with capacitor without ripple current rating?
                      by chth96
                      When I tried to repair LG 29 inch CRT TV, I found that the ESR value of samyoung SMS capacitor(160v 2.2uf), which is very close to D1879 transistor, is 6 ohm.


                      Judging from above ESR Meter Table,I think It is necessary to replace this sms capacitor.So I visited local electronics shop,and I purchased 160v 2.2uf rubycon YK capacitor.
                      But when I browse through rubycon YK datasheet,I found that there is no ripple current rating for 160v 2.2uf specification. But On the contrary, I found 39 mA ripple current rating for 160v 2.2uf SMS capacitor.
                      Rubycon YK DataSheet (b...
                      04-19-2024, 05:19 AM
                    • Ady2017
                      Are there any datasheets available for Elna RJG capacitors?
                      by Ady2017
                      I have a 2007-era Panasonic VHS combo that is full of of Elna RJG capacitors. I am trying to test the capacitors to diagnose the machine and then select replacement capacitors but I can not find any datasheets for them. I did find a Elna catalogue from 2007-2008 but there is no mention of this capacitor series. Where these specially made for Panasonic and so not made available to the public? Any ideas what to find out what the ESR values should be without the datasheets? They are all between 10V and 50V and 47uF and 1800uF. None are leaking or bulged but I know that they need to be tested to be...
                      05-25-2025, 02:19 PM
                    • ctroxtell
                      Samsung UN70tu7000wxza no standby light, do I have bad capacitors?
                      by ctroxtell
                      I picked up a 70" Samsung UN70TU7000WXZA. The original owner said they were watching it when the power surged and knocked it out. I pulled the back off the TV and disconnected the main board from the power board, and the LED backlight came on, which I was told meant the power board was good. When everything is plugged in the standby light will not come on, looking at the main board BN94-17775A with a thermal imaging gun I can see one of the chips labeled 3202 is 251 degrees F just sitting idle. I found a replacement board, BN94-16115X; this board has the same symptoms, except it is a different...
                      01-03-2025, 08:57 PM
                    • Loading...
                    • No more items.
                    Working...