Operating caps well below rated voltage

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Perry Babin
    Member
    • Apr 2024
    • 15
    • usa

    #1

    Operating caps well below rated voltage

    I think this has been answered but I couldn't find the thread.

    Someone asked me if it would harm a capacitor (10F [not a typo], 24v) if it was operated on nothing more than 12v.

    So, I ask... Does it change any of the capacitor's characteristics/parameters/? in any way if it is never operated near rated voltage?

    If operated for years at 1/2 rated voltage, does it accept full rated voltage like it would if it had always been operated at the higher voltage?

    Or would it require reforming?
  • andrewsawesomr
    Senior Member
    • Jun 2022
    • 100
    • United States of America

    #2
    Operating caps well below rated voltage is fine, however, over time the cap will need to be slowly risen up to its rated voltage if you want to use it at the rated voltage again.

    Comment

    • Perry Babin
      Member
      • Apr 2024
      • 15
      • usa

      #3
      +1

      Comment

      • CapLeaker
        Leaking Member
        • Dec 2014
        • 7986
        • Canada

        #4
        That depends on how much below rated value you go.

        For shits and giggles let’s say you use a 200v cap and only have 12v on the rail, that is not a good idea. 25V cap on a 12V rail, is perfectly fine.

        Comment

        • sam_sam_sam
          Badcaps Legend
          • Jul 2011
          • 6024
          • USA

          #5
          Originally posted by CapLeaker
          That depends on how much below rated value you go.

          For shits and giggles let's say you use a 200v cap and only have 12v on the rail, that is not a good idea. 25V cap on a 12V rail, is perfectly fine.
          What is the best practices should you follow when using a capacitor voltage values because in rare occasions I will use a capacitor with a voltage of 50 volts on a 12 volt switching power supply circuit

          I guess this is a valid topic to discuss with what would be an acceptable general rule of thumb to follow
          Last edited by sam_sam_sam; 06-02-2024, 05:43 PM.

          Comment

          • CapLeaker
            Leaking Member
            • Dec 2014
            • 7986
            • Canada

            #6
            sam_sam_sam
            I go by the rule of roughly double the voltage rating vs what the voltage rail is. However this doesn’t work 100% of the time, because of size etc… and also depends on what circuit.
            A different problem is when you need caps in stock. Mostly I have 50V caps but I also have common capacities in 25V format. Then I got a very few odd 63V caps that I need occasionally. Primary filter caps I don’t stock period as they are rather expensive. Weird or large capacities I usually order. The brands I use are Panasonic, Nichicon, Rubycon and very seldom a 4th brand all are 105C rated and order them from a trusted supplier, not eBay or AliExpress etc. So far so good, never had a return of any of my capacitors that I put in fail yet.

            Comment

            Related Topics

            Collapse

            • electron_jj
              Panasonic TH-L42D25A checking the PSU output voltage
              by electron_jj
              Hi Everyone, I am new to this forum. I have a Panasonic LED TV which doesnt turn on and is blinking 4 times repeatedly when I turn on the switch. The TV does not respond to the remote control so I had to turn on using the physical switch on the side of the TV. When I turn on the switch the 4 x blinking starts and repeat itself until I turn off the TV. There is a black screen. I turned off the light in the room to check the panel and I think there is no backlight as far as I can tell.

              I have been inspecting and testing the capacitors and diodes in the power supply board to try to...
              08-29-2021, 08:13 AM
            • sam_sam_sam
              Trip light 2400 watt line conditioner bought used issue with low voltage oscillation going on between relays
              by sam_sam_sam
              I found two capacitors on the board and one of the leads on one capacitor had bad soldering joint and the other joint connections not much better and there were several soldering joints that way to much flux around the joint redid several of them

              The capacitors were a non brand that I did not recognize they got replaced and now it does not oscillating between relay but what concerns me a little bit is when the voltage is a little bit low the output voltage is around 130 volts and then drops down to 115 volts this happens around 105 to 108 volts if remember correctly

              Now...
              06-09-2024, 10:57 AM
            • Document Archive
              ISL95831HRTZ ISL95831HRTZ-T ISL95831IRTZ ISL95831IRTZ-T Voltage Regulator Datasheet
              by Document Archive
              3+1 Voltage Regulator for IMVP-7/VR12 CPUs

              Compliant with IMVP-7/VR12, the ISL95831 provides a complete solution for microprocessor and graphic processor
              core power supply. It provides two Voltage Regulators (VRs) with three integrated gate drivers. The first VR can be
              configured as 3-, 2- or 1-phase VR while the second output is 1- phase VR, providing maximum flexibility. The two VRs share the
              serial control bus to communicate with the CPU and achieve lower cost and smaller board area compared with the two chip approach.
              Based on Intersil's Robust Ripple Regulator...
              11-05-2024, 03:24 PM
            • ruletero
              Acer a515-43 low battery charge voltage
              by ruletero
              Hi

              Acer A515-43
              LA-H801P

              Fail: Does not charge battery, has low voltaje on connector.

              Laptop didn't want to turn on, only charge led blinked.

              I found PQB5 (mosfet high battery charger) in short, voltaje in +12.6V_BATT was 19 v ...

              I changed it, changed PQB6 too and now battery charger voltage is 4.4V but battery is 3 cell, 11.25v, then is very low to charging.

              Laptop turns on without battery and works fine, but with battery turns on and turns off inmediately, I suspect battery bad but I don't know...
              10-24-2022, 02:31 PM
            • sam_sam_sam
              Adjustable Boost Power Supply DC-DC Constant Voltage Current Charging Module
              by sam_sam_sam
              I want to know if I could hook up a solar panels to this boost converter would I have any issues doing and I would have issues what would they be

              Adjustable Boost Power Supply DC-DC Constant Voltage Current Charging Module

              https://www.ebay.com/itm/116497313155?var=416785404161


              Here are some of the description from the eBay seller

              The main parameters:
              1. Product name: High-power non-isolated DC boost module power supply.
              2. Product model: 100A2000W.
              3. Input voltage: DC12V-60V.
              4. Input current: 100A (maximum)....
              05-18-2025, 09:45 AM
            • Loading...
            • No more items.
            Working...