value of this cap please

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • shaunbt123
    Senior Member
    • Nov 2012
    • 119
    • uk
    #1

    value of this cap please

    can someone please tell me the value of this cap please,and also the voltage. and also wheres the best place to buy a replacement in uk.
    thank you.
    Attached Files

    if you find these attachements useful please consider making a small donation to the site

    Tags: None
    • mr2013e
      Elc. Engineer
      • Jul 2013
      • 41
      • TURKEY
      #2
      Re: value of this cap please

      10nf 1250v

        Comment

        • selldoor
          Slow Learner
          • Dec 2010
          • 7870
          #3
          Re: value of this cap please

          Its a 10nf 3% tolerance 1250v


          http://uk.rs-online.com/web/p/polypr...itors/1908602/
          Last edited by selldoor; 01-30-2014, 01:34 PM.
          Please upload pictures using attachment function when ask for help on the repair
          http://www.badcaps.net/forum/showthread.php?t=39740

            Comment

            • shaunbt123
              Senior Member
              • Nov 2012
              • 119
              • uk
              #4
              Re: value of this cap please

              thank you.when i put my meter across it it reads 1.896nf so i assume its bad.

                Comment

                • selldoor
                  Slow Learner
                  • Dec 2010
                  • 7870
                  #5
                  Re: value of this cap please

                  Is that off the board? They are not expensive gueass postage racks up the cost
                  Do RS have a trade desk near you?
                  CPC have free delivery at the moment but I couldnt see one - you could try - easy to miss!!!
                  Please upload pictures using attachment function when ask for help on the repair
                  http://www.badcaps.net/forum/showthread.php?t=39740

                    Comment

                    • shaunbt123
                      Senior Member
                      • Nov 2012
                      • 119
                      • uk
                      #6
                      Re: value of this cap please

                      that reading is with the cap in circuit.i will desolder the cap tommorow and post back the reading.
                      thank you.
                      ps.ive just checked my nearest rs trade counter is 38 mile away other than that its £6.34 delivered .
                      Last edited by shaunbt123; 01-30-2014, 02:02 PM.

                        Comment

                        Previous template Next

                        Related Topics

                        Collapse
                        • Logix_UK
                          PS5 Capacitor Value
                          by Logix_UK
                          Hi Everyone. I need to replace a capacitor on a PlayStation 5, the picture below shows the cap which is next to the WiFi component. I have removed the cap below and it looks like 10nF however my multimeter is jumping a bit and it’s not east to get the probes on both ends. Can someone really help me out and confirm the value of this cap if you know it please?...
                          10-15-2025, 12:39 AM
                        • titomno2
                          Acer AN515-52 SATA1 port not working no hdd detected in BIOS...
                          by titomno2
                          Hi guys,
                          On motherboard ACER AN515-52 type LAF951P.
                          I fixed issue with not starting computer (it was the PQ201 component not working properly).
                          But after checking everything I have still an issue with secondary SATA connector JHD1 (for HDD typically).
                          Basically some HDD spin but are not detected by the bios.

                          ​

                          Already tried following:
                          checked the 4 data lines
                          #2 RDSATA_PTX_C_DRX_P4 => CO18 (10nF seems OK) => RO24 (0Ohm measured at 0.25Ohms).
                          #3 RDSATA_PTX_C_DRX_N4 => CO17 (9.68nF seems OK) => RO23 (0Ohm measured...
                          07-28-2024, 08:30 AM
                        • mikkele86
                          Luxman R-5045 - Capacitor at amplifier output broke, can i replace with higher capacitance ?
                          by mikkele86
                          Hello Im renovation a Luxman R-5045

                          On the attached picture there is a cap 0.047uF (47nF) and a resistor, 10ohm. What is their purpose ? and what would happend if I were to replace the caps with lets say, 10nF or 100nF ?
                          because thats what i got in stock :/

                          ​...
                          1 Photo
                          04-16-2024, 12:37 PM
                        • llonen
                          Kenwood TS830s
                          by llonen
                          This hybrid radio came in for what is a typical repair for these venerable vintage sets, band-changer control inter-coupler had parted company and left the building. I was going to machine a replacement but I found a supplier for suitable substitutes, anyways further inspection of the RF cage found a cracked snubber capacitor (10nf) a good inch in diameter. So I ordered replacements rated for 2KV the high voltage in this area is around 800 volts, seemed a reasonable compromise, other than the bad solder joints on the valve bases the repair was progressing nicely.

                          Well when the parts...
                          10-02-2019, 04:19 PM
                        • MichR
                          Yoga 700 11ISK multiple shorts
                          by MichR
                          I've got this Yoga laptop for a reasonable price. Seller said it suddenly turned off. However, he or someone else tried to repair it, making the situation even worse: he told me the NPCE388 has been replaced, but nothing else was done.
                          Actually, some power supply jumpers have been desoldered. Sadly, all of these rails are shorted to ground.
                          Before going on, take a look at the motherboard. This is the best quality picture I could find of it:


                          And this is a particular of my board:


                          I could not find any schematics of this board over the web....
                          06-16-2018, 02:08 AM
                        • Loading...
                        • No more items.
                        Working...