Akai 27" Turns on and off and on and....

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • hoadle
    Senior Member
    • Jul 2010
    • 174
    #21
    Re: Akai 27" Turns on and off and on and....

    I fixed an LCD monitor with a similar issue. It ended up being a shorted transistor (mrosenberg42)
    where transistor (inside mainboard or power supply board)?
    Last edited by hoadle; 01-15-2011, 01:34 PM.

      Comment

      • hoadle
        Senior Member
        • Jul 2010
        • 174
        #22
        Re: Akai 27" Turns on and off and on and....

        I fixed an LCD monitor with a similar issue. It ended up being a shorted transistor (mrosenberg42 add)
        where transistor (inside mainboard or power supply board) Mr mrosenberg42?

          Comment

          Previous 1 2 template Next

          Related Topics

          Collapse
          • Tynan Dill
            Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
            by Tynan Dill
            I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

            Upon bringing it home and plugging it up, it showed a standby light.

            I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

            The screen seems to blackout and stay black, but with a flashlight I can see the display.

            With my Playstation 4 connected via HDMI, and running a game I can hear sound.

            Assuming...
            ORIGINAL POWER SUPPLY BOARD
            7 Photos
            11-22-2024, 01:46 PM
          • sam_sam_sam
            Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply
            by sam_sam_sam
            I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

            One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
            03-31-2024, 02:12 PM
          • sumilumi
            700mv ripple on Akai Sampler linear supply
            by sumilumi
            Hi fellow troubleshooters. This is my first post on badcaps. I've recently setup an electronics workbench. i'm also building a studio with old equipment bought faulty at low cost.
            I've been into electronics since the mid 80's and particularly in the last few years though only getting hands on with repairs now. My knowledge gaps are significant so I'll be posting here to seek guidance advice and general practical applied learning.

            On my bench today is an old ca. 1993-95 Akai hardware sampler. This runs on both a linear and Smps supply. Both are getting on in age and ripple...
            01-02-2022, 10:12 AM
          • sam_sam_sam
            Modification to a ZD-987 desoldering/soldering station using a external switching power supply
            by sam_sam_sam
            I have been working on this concept for quite some time now with limited success but recently I found a switching power supply that is setup for the voltage that this soldering station needs to operate at however it also needs part of the secondary circuit from the original switching power because you need several voltage rails

            I once tried to get a ZD-915 desoldering station to work on a 18 volt battery power supply but unfortunately things did not go well but I did find a work around but I might try this idea again but going at a little differently more about this another time...
            07-01-2024, 06:34 AM
          • shamsudeen
            Hi, Can we use SMPS Bench Power Supply for Laptop troubleshooting?
            by shamsudeen
            Hi all, I just need to know that, can i use SMPS type power supply to test and short circuit detection on a laptop motherboard?
            I saw 95% of repair guys are using only Linear bench power supply. linear bench power supply is pricy, thats why i planned to get one SMPS supply.

            i know that in linear power supply the noise will be very low comparing to SMPS supply....
            Today, 07:14 AM
          • Loading...
          • No more items.
          Working...