Samsung 50uhd8550 standby led pressing power button does not turn TV on

Collapse
X
Collapse
 
  • Page of 4
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 template Next
  • waakye
    Badcaps Veteran
    • Dec 2018
    • 340
    • Electronada
    #61
    Re: Samsung 50uhd8550 standby led pressing power button does not turn TV on

    Change DS811 and the power supply is back to life. Thanks all for helping. It was a learning experience for me.
    Attached Files

      Comment

      • nomoresonys
        Badcaps Legend
        • Jan 2013
        • 12141
        • U.S.
        #62
        Re: Samsung 50uhd8550 standby led pressing power button does not turn TV on

        You tested that diode in post #22, must have gotten a bad reading.

          Comment

          Previous 1 2 3 4 template Next

          Related Topics

          Collapse
          • PNI E.
            Samsung ue55tu7170u not turn on and no standby led main bn9650990e
            by PNI E.
            Hi guys, I’m back here my friend give me her tv, that doesn’t turn on and no standby red led. When u plug in the cord the red led of one two second is on, then turn off. If you push the power button or the remote the red led blinks but nothing happen. I give u some photo with voltage, don’t look the fuse….because I blow it for mistake nd I dint have the right replace so I just put it for test the tv. The standby voltage should be 11,88 volt on the diode, but I have 13 volts. I put in the photo the different volts I test and there are someone negative…I don’t know if it s normal. On...
            03-17-2025, 04:23 AM
          • Document Archive
            Samsung Galaxy Book 2 Notebook Specification for Upgrade or Repair
            by Document Archive
            This specification for the Samsung Galaxy Book 2 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Galaxy Book 2 boardview and Galaxy Book 2 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
            09-07-2024, 05:50 AM
          • tvguy12012012120
            Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
            by tvguy12012012120
            This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

            Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
            02-07-2025, 05:13 PM
          • ChristianBr01
            LED TV Samsung The Frame 55 inch QE55LS03RAU Standby Light only
            by ChristianBr01
            Hello everyone,
            I got a Samsung The Frame 55 inch TV for free from uncle cause it is not turning on anymore. I am in the second year of training as an electrician so I have knowledge already but I am far away from to be a pro.
            The TV has Standby but ist not turning on. A Friend of mine owns a 50 inch Frame TV so I checked the One Connect Box and the One Connect Cable there. Both are good and working normally. I have opened the TV case and measured some voltages on the Board.
            What I already found is that the 12.8V are not an the connector to the main board connector to the power...
            04-23-2025, 01:48 AM
          • Jackching
            Samsung UN46EH5000F wont turn on. Blinks red standby light continuously
            by Jackching
            I know for sure it has a bad cap and one cold solder joint. Just wondering before i order the Caps if anyone has any experience with this model? Just making sure there isnt a common component that goes bad besides the caps....
            04-15-2024, 05:14 PM
          • Loading...
          • No more items.
          Working...