LG 60PB660V Plasma tv Help Please

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • thuss
    Badcaps Veteran
    • Jul 2012
    • 321
    • uk
    #21
    Re: LG 60PB660V Plasma tv Help Please

    Originally posted by raybla
    Hi Pat P & Chrismurphy thanks for your input, This is what I found on the Ysus panel Q552/Q553 shorted R559 o/c replaced with the correct parts
    C873 on top buffer board blown not sure what value is here had another board handy - tv now repaired many thanks all
    Hi Raybla are you saying that replacing theses three components got your 18v back - I'm a bit confused I was under the impression that your ysus was previously given the all clear?

    On my ysus board 507 q552/553 and r559 are not reading faulty.

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • MisterAIL
        PS5 digital / No Power / No Beep / Good power supply
        by MisterAIL
        Hi everyone,

        Brought a non functionnal PS5. Apparently only a bad PSU...
        No beep, nothing.

        After some tests i found this :
        - PSU is fine (12 volts stable)
        - 12 volts line is shorted
        - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
        - By the way, nothing change. No signal, no power, no beep.

        Mesuring all rails with my workbench psu (12 volts input)
        - 0.00 amp drawing
        - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
        3.3v PMIC
        5 Photos
        03-12-2024, 03:24 PM
      • Mcfeetroy
        Fishing bite alarm drains battery
        by Mcfeetroy
        Good day to all. The bite alarm drains 9-volt Krona batteries. Current consumption when switched on is about 50 mA. I wiped the board from oxides, I will attach a photo (on the board there is a j3y transistor and a 7533 stabilizer, the microcircuit is erased = (the 3.3-volt stabilizer heats up weakly. I replaced it, nothing changed. I unsoldered the microcircuit, the consumption disappeared. The resistance on the pins of the unsoldered microcircuit from the point clockwise is more than 2 megaohms, the 11th leg is presumably ground. I warmed up the microcircuit, the consumption does not change....
        08-01-2025, 03:52 AM
      • BTubbs200
        Dead Dell Latitude 5420 not receiving 20 volts from USB-C charger
        by BTubbs200
        Hello,

        Dell Latitude 5420 P137G
        Board: LA-K491P REV A01

        I have received this laptop which was described as "does not power on or accept charge." Battery shows no sign of charging when charger is plugged in, nor does the board show any signs of life when battery is unplugged and charger is plugged in. No light from the LED at all or any other indications of activity.

        Board seems to have no shorts, all power rails are fine and show high resistance.

        When charger is plugged in, voltage is present in 3.3V rail but absent in others....
        01-24-2025, 08:15 PM
      • sam_sam_sam
        MPJA 10 AMP @ 0 to 30 Volts Switching Power Supply Cap Fault
        by sam_sam_sam
        I have this 10 amp 0 to 30 volt switching power supply that decided to have a 630 milliamperes draw on it at 0 volts

        I open it up to find non brands name capacitors in it

        I am not sure how this switching power supply is set up

        Could someone please explain how this power supply works

        Here is the capacitor ESR results

        (1) 47uf@50 volts 0.46
        (2) 47uf@50 volts 0.45
        New 47uf@50 volts 0.35

        (1) 100uf@25 volts 0.34
        (2) 100uf@25 volts 0.35
        New 120uf@50 volts 0.08

        (1) 220@25 volts 0.13...
        10-21-2018, 10:02 AM
      • Truncatedhose
        Help repair this relic? Philips 42PF7220A/37, pulsing buzz from YSUS
        by Truncatedhose
        Greetings all!

        Originally this set had the usual messed up video symptoms such as: horizontal lines, weak, grainy video, bottom and top of picture differ in intensity of problem. It also seemed to slow to turn on or show the messed up picture.

        Seemed like must be YScan/buffer board failure. Ordered buffer boards from my distributor which were supposed to be original/new and also from another distributor, I ordered the YSUS because I wanted to replace it for preventative maintenance. (also, the YSUS had a bulged cap, so there was even more reason to suspect it could...
        07-04-2018, 10:59 AM
      • Loading...
      • No more items.
      Working...