LG 60PB660V Plasma tv Help Please

Collapse
X
Collapse
 
  • Page of 2
  • Time
  • Show
Clear All
new posts
Previous 1 2 template Next
  • thuss
    Badcaps Veteran
    • Jul 2012
    • 321
    • uk
    #21
    Re: LG 60PB660V Plasma tv Help Please

    Originally posted by raybla
    Hi Pat P & Chrismurphy thanks for your input, This is what I found on the Ysus panel Q552/Q553 shorted R559 o/c replaced with the correct parts
    C873 on top buffer board blown not sure what value is here had another board handy - tv now repaired many thanks all
    Hi Raybla are you saying that replacing theses three components got your 18v back - I'm a bit confused I was under the impression that your ysus was previously given the all clear?

    On my ysus board 507 q552/553 and r559 are not reading faulty.

      Comment

      Previous 1 2 template Next

      Related Topics

      Collapse
      • supermattch
        HP 15dy-2021nr wont power on mystery volts
        by supermattch
        Hi everyone.

        I am diagnosing my personal laptop, because it wont power on and no leds light up.

        At the dc-in there are 8 pins, 1 and 2 shows healthy 19.66 volts. The next three are ground, but the 6th one shows .283 volts. This is strange to me, it should be 3.3 or 5 or aome volts not 0.283v. As I am new to this, I would like some guidance. Please someone advise me on what to check next.

        Oh the boardview and schematics I am using is for a similar model as I cannot find the proper one anywhere. Quanta DA0P5HMB8F1 rev F. Nowhere on the internet.
        09-23-2025, 12:13 PM
      • PlasMatt
        LG 60PV450 Possible Bad YSUS Need help confirming Diagnosis
        by PlasMatt
        I have an LG plasma that after reading through a bunch of posts and doing some testing I believe has a bad YSUS board. The problem is that that doesn't make sense to me for some of the symptoms. The problem started yesterday. While watching a movie the TV just shut down like I pressed power. I have it hooked to a PC and use RS232 to turn it off and on so I thought maybe something had glitched there. I turned it back on and finished the movie with no problems. The same thing happened today so I checked logs to see if something in the control glitched and sent an off command but it didn't, After...
        09-20-2025, 06:50 PM
      • MisterAIL
        PS5 digital / No Power / No Beep / Good power supply
        by MisterAIL
        Hi everyone,

        Brought a non functionnal PS5. Apparently only a bad PSU...
        No beep, nothing.

        After some tests i found this :
        - PSU is fine (12 volts stable)
        - 12 volts line is shorted
        - DA9065 was fried, F7003 also => Replaced both of them, short is gone on 12 volts line, no dead short anywhere else.
        - By the way, nothing change. No signal, no power, no beep.

        Mesuring all rails with my workbench psu (12 volts input)
        - 0.00 amp drawing
        - 12 volts, 5 volts, 2 volts, 1,15 volts are presents (suppose new DA9065 do is...
        3.3v PMIC
        5 Photos
        03-12-2024, 03:24 PM
      • Mcfeetroy
        Fishing bite alarm drains battery
        by Mcfeetroy
        Good day to all. The bite alarm drains 9-volt Krona batteries. Current consumption when switched on is about 50 mA. I wiped the board from oxides, I will attach a photo (on the board there is a j3y transistor and a 7533 stabilizer, the microcircuit is erased = (the 3.3-volt stabilizer heats up weakly. I replaced it, nothing changed. I unsoldered the microcircuit, the consumption disappeared. The resistance on the pins of the unsoldered microcircuit from the point clockwise is more than 2 megaohms, the 11th leg is presumably ground. I warmed up the microcircuit, the consumption does not change....
        08-01-2025, 03:52 AM
      • BTubbs200
        Dead Dell Latitude 5420 not receiving 20 volts from USB-C charger
        by BTubbs200
        Hello,

        Dell Latitude 5420 P137G
        Board: LA-K491P REV A01

        I have received this laptop which was described as "does not power on or accept charge." Battery shows no sign of charging when charger is plugged in, nor does the board show any signs of life when battery is unplugged and charger is plugged in. No light from the LED at all or any other indications of activity.

        Board seems to have no shorts, all power rails are fine and show high resistance.

        When charger is plugged in, voltage is present in 3.3V rail but absent in others....
        01-24-2025, 08:15 PM
      • Loading...
      • No more items.
      Working...