vestel smart tv when I plug in the stanbay light does not turn on the voltage does not turn out the socket is going out + 12volt and +24 volts when the controller +12 volts short circuit cause cause I can detect the fault 17mb95 anakart
-
-
Re: vestel smart 40 pf7070 led tv is not working
this is the motherboard powerborAttached Files -
-
Re: vestel smart 40 pf7070 led tv is not working
The images are to small. Can you post them again please.
Görüntüler küçüktür. Tekrar gönderebilir misin lütfen?Willing to help but I'm no expert.Comment
-
Re: vestel smart 40 pf7070 led tv is not working
FotoAttached FilesComment
-
-
Re: vestel smart 40 pf7070 led tv is not working
What voltages do you have on the pins of PL200
PL200'ün pinlerinde hangi voltajlar var?Attached FilesWilling to help but I'm no expert.Comment
-
-
Re: vestel smart 40 pf7070 led tv is not working
there is no voltage, but when I remove the socket +12 and +24 volts, the controller shows a +12 volt short circuitComment
-
Re: vestel smart 40 pf7070 led tv is not working
Check the diodes D318, D319, D320, D321 , D328Attached FilesWilling to help but I'm no expert.Comment
-
-
Re: vestel smart 40 pf7070 led tv is not working
The diodes that you are saying are +12 and +24 volts when you remove the socket to the solid motherboardComment
-
Re: vestel smart 40 pf7070 led tv is not working
With the television switched off use your multimeter set to diode mode and check any of the diodes mentioned above to see if any of them are short circuit.
Televizyon kapalıyken multimetre cihazınızı diyot moduna ayarlayın ve herhangi bir kısa devre olup olmadığını görmek için yukarıda belirtilen diyotları kontrol edin.Willing to help but I'm no expert.Comment
-
Re: vestel smart 40 pf7070 led tv is not working
Picture the 0 ohm smd pole in picture iscapacitorAttached FilesComment
-
-
Re: vestel smart 40 pf7070 led tv is not working
The 0 ohms smd is a zero ohm resistor which looks as though it is being used as a fuse.Willing to help but I'm no expert.Comment
-
Re: vestel smart 40 pf7070 led tv is not working
Hemen asasigindaki 2 adet smd kutupsuz kondansator kisa devreComment
-
Re: vestel smart 40 pf7070 led tv is not working
You need to unsolder them carefully and check them for short circuit. Do not lose them.
Bunları dikkatlice çözmeli ve kısa devre için kontrol etmelisiniz. Onları kaybetme.Willing to help but I'm no expert.Comment
-
Re: vestel smart 40 pf7070 led tv is not working
Well done.
AferinWilling to help but I'm no expert.Comment
-
Dear friends,
i do have a VESTEL 17MB82S not working. Here is the story:
First, when i give power on tv, red led lights after some blinkings and i've noticed that picture apears but no backligt at all (i use a small light to see it).
Then i do flash with a FAT32 USB stick, the upgrade_loader.pkg file with the known OK button method. After that, the TV stops and when i press the ON-OFF button from remote control, the red led goes on but no backlight no picture at all.
I do took off the 2 flash IC's U10,U12 try to read them with flash programmer, but i get "Error... -
Working BIOS for this model:
Model: EXO SMART XQ3C-X79
Board: EM_CM218_78B_V2.0
SN: 1213212A00016...07-19-2024, 01:10 PM -
Hy guys, i have this Audi smart key with a touch screen not working, the key has a 450 mA battery inside that looks ok on the multimeter, but when connecting the usb c on the board there is no power consumption, no current going to the board. Has anyone worked on these before?...
-
The tv is a Toshiba 55u5766dg, made by Vestel.
Sound: yes
Picture: no
That is, when powering up the tv, the indicator leds starts blinking and at a certain moment during the booting, (let's say afer 3-4 seconds) the screen lights up and shows the Toshibo logo for a second, then the screen goes black until a short flash a couple of seconds later and the indicatorled turns green. The screen stays black: no backlight and no picture
When a connect a harddiskrecorder playing a recorded media, there's sound but no screen. Even with a torch... -
Hello,
i have many 5050sff. all of them, and how i experienced over many years for all about 250 DELLs goin through my hands, are fully flashable and can be serviced in any way when the service_mode jumper is set.
Never ever i experienced problems with that.
Now i have one 5050sff machine, where this jumper isnt working at all.
I do not get the normal messge that the jumper is set when booting and a short test with FPT just confirms this. Everything is locked -->> EVEN for reading !?
The history of the machine is that i used it in my office...
Comment