TV Blaupunkt B32FA112BK stuck in standby

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • lepak06
    Senior Member
    • Feb 2017
    • 51
    • france
    #1

    TV Blaupunkt B32FA112BK stuck in standby

    Hi

    I've an TV Blaupunkt B32FA112BK stuck in standby (red led)
    I can't power on. I checked all voltage . They are ok.

    The first time , i flashed the eprom 25q32 and the tv worked few day.
    One day i unplugged the AC cable and the puggled it then the tv is stuck in red led. I retry to flash eprom and change eprom with another but always stuck in red led.

    Do you have any idea?
    Tags: None
    • lepak06
      Senior Member
      • Feb 2017
      • 51
      • france
      #2
      Re: TV Blaupunkt B32FA112BK stuck in standby

      up

        Comment

        Previous template Next

        Related Topics

        Collapse
        • lepak06
          TV LED 4K Selecline 65S18 ( T.MS3458.U801) stuck in Standby mode
          by lepak06
          Hello

          I have an TV Led 4K Selecline 65s18 with mainboard T.MS3458.U801

          The TV is faulty with stuck in Standby RED LED. Can't power the TV.

          Before this problem , the TV stuck the picture with artefact , i unplug the AC cable and since the tv is stuck in standby .

          All voltage are OK on PSU and main board for regulator. I tried flash firmware 25Q64 with many dumps

          But the voltage on power button is 0.6V not 3.3V. When i press power button the voltage up to 0V. I tried to add 5V with Power Supply on 5V_STB and 3.3V on Power...
          01-12-2023, 01:43 AM
        • cockalomg
          Blaupunkt blaupunkt b32she188tchd-100 no standby light
          by cockalomg
          Does anyone have a schematic for this board?
          I have no output voltages, no standby voltages.
          The fullbridge rectifier has a permanent 330V
          there is no voltage on the two large black electrolytic capacitors​
          2 Photos
          11-05-2024, 03:01 AM
        • toty79
          Hisense LTDN50K220WSEU stuck in standby
          by toty79
          Hello to all friends of the forum and well found, here I am asking for your help and sorry for my translated English.



          As per Hisense tv title LTDN50K220WSEU stuck in standby
          PSU rsag.820.5687 HLL 4855WF
          Main rsag 7.820.5842
          I enclose the psu diagram, after the first routine checks I find myself with a regular standby voltage of 3.3v blue light on steady when the power button is pressed nothing happens, psu disassembled and bench checked ... forced ignition by sending a signal 3 , 3v on the SW and PWM2 pins the psu turns on and delivers all the voltages...
          05-01-2022, 04:39 PM
        • lego1234567
          LG 32LB1R - stuck in standby mode
          by lego1234567
          Hi. I have the following problem with my TV. After connecting to mains, the standby led (red) turns on, but TV is not responding to remote control or buttons on TV. After some measurements, I found out that +5 V standby voltage is present, but I dont have ON/OFF signal coming in to turn PSU on. It stays at zero volts. After looking at the schematic of the mainboard, I should get ON/OFF signal coming in at the R1402 resistor, but it stays around +3,5 V. So I removed it and I was able to turn on TV with buttons on TV, but not with remote control.

          What could be the problem ? Thanks...
          2 Photos
          01-21-2024, 03:39 AM
        • Rusenga
          Samsung UA39EH5003R Stuck on standby
          by Rusenga
          Hi techs, I have a Samsung ua39eh5003r which switches on and then goes to standby. I have to wait for a day or two for the tv to switch on again, all the time it is stuck on standby. I have checked the voltages on the power supply board on both occasions when it is on and off and these are my findings:

          Connector CNM803:
          TV ON
          Pin1,3,4,5(Vamp),7(Vamp)- 12.6V; Pin2(PWM_DIM)- 0.96v; Pin6(BLU_ON/OFF)- 4.41v; Pin8,9,10- grnd; Pin11,12,13- 5.16v; Pin14(Power ON/OFF)- 3.3v

          TV OFF
          Pin1,3,4,5(Vamp),7(Vamp)- 12.6V; Pin2(PWM_DIM)- 0.06v; Pin6(BLU_ON/OFF)-...
          09-18-2021, 11:51 AM
        • Loading...
        • No more items.
        Working...