Lg 47 led flashes then goes off

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • deegee2016
    Member
    • Apr 2016
    • 11
    • england

    #1

    Lg 47 led flashes then goes off

    I have an LG47ODUE that shows LG Logo then goes black under torchlight image is visible.


    Power supply board tests:

    Standby voltages: in order on connector:

    9) Ground - Ground = 0.0v
    8) 12v - NC = 11.95v
    7) 12v - 12v = 11.95v
    6) Ground - Ground = 0.0v
    5) 24v - 24v = 24.77v
    4) Ground - Ground = 0.0v
    3) 3.5v - PDIM2 = 3.54v
    2) 3.5v - PDIM1 = 3.55v
    1) PwrOn - DrvOn = 3.42v

    Most voltages not present until standby button is pressed

    Led Connector Tests:

    106v down to 82.2v at led connector on both lines. LEDs connected

    115v down to 82.2v at led connector on both lines. LEDs disconnected.

    Diode Side Test: (red probe to cathode side and black to test points at led connector)

    97v and decreases - cathode side of diode to test point at led connector.

    LEDs have been checked out of the unit on a DC power supply two strips at 30v all LEDs work.

    Work has been carried out previously as jumpers on led strips. Work fine out of unit on DCPS.

    I had image but no backlight.

    Could this be a caps issue???

    Does the TV need all LEDs connected to work correctly (ie) cut out if not enough LEDs for load.

    Obviously 88.2v is not enough to drive the leds

    Regards Dee
  • budm
    Badcaps Legend
    • Feb 2010
    • 40746
    • USA

    #2
    Re: Lg 47 led flashes then goes off

    Please stick to ONE THREAD!
    Never stop learning
    Basic LCD TV and Monitor troubleshooting guides.
    http://www.badcaps.net/forum/showthr...956#post305956

    Voltage Regulator (LDO) testing:
    http://www.badcaps.net/forum/showthr...999#post300999

    Inverter testing using old CFL:
    http://www.badcaps.net/forum/showthr...er+testing+cfl

    Tear down pictures : Hit the ">" Show Albums and stories" on the left side
    http://s807.photobucket.com/user/budm/library/

    TV Factory reset codes listing:
    http://www.badcaps.net/forum/showthread.php?t=24809

    Comment

    Related Topics

    Collapse

    • Pipolups
      Corsair K70 LUX RGB dying LEDs
      by Pipolups
      Hi there !

      I'm having an issue for several weeks with my quite old K70 LUX RGB keyboard. I haven't used it for few months, and once I setup up again my desktop computer, I got several dead LEDs on that keyboard. I tried the Corsair troubleshooting thing (disabling options in iCUE, ...) but nothing changed so I conclude that for some reason some LEDs went in retirement...😅
      Decision taken to change these LEDs as I have access to desoldering iron and binocular magnifier, I wrote a ticket to tech support, hopping to obtain the LEDs reference and... They refused to tell me 🙄...
      10-08-2024, 11:58 AM
    • Bigfoot
      Samsung TV UN60J6200AF No Display + No LED
      by Bigfoot
      Hi guys
      I'm working on similar Samsung TV UN60J6200AF.
      When I plug in power cord, the red light lights up, and flashes, then turns off.
      I measured on the power supply board, and even without pressing the power on zbutton in getting on CNM803 (which goes from Power supply to Main board):

      UD = 2.3V
      PMW_BLU4 = 3.3V
      PS_ON = 4.4V
      A13V = 12.75V

      I looked at the manual and all the voltages are correct.
      When I unplug the main board from the power supply, LED lights are supposed to come on. However, non do come on.
      ...
      06-20-2023, 10:24 PM
    • odie34
      Sony OLED XR-77A80J - 5 Flashes But Turn On After Hard Reset
      by odie34
      I am a hobbyist (not a professional) so please be gentle...

      I recently received an XR-77A80J that wouldn't turn on. (Repeating 5 flashes when plugged in.)

      I did a hard reset by holding the power button for about 30 seconds until the set powered down. I then tried to turn it on and it powered up, bringing me to the setup screen. There's not a lot of detail on the setup screen but the picture didn't have any distortions, so at least a cursory examination suggests no physical damage to the screen. The set appeared to be working normally, but it shut down after about 15 seconds,...
      02-18-2024, 09:11 AM
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • TrisHCl
      LED TV Boot loop - UE40F6500SB
      by TrisHCl
      Hi,

      First post...

      I have this TV, which was working, then suddenly would not turn on. It would get the clicking relay then flash up the screen for less than a second, off for a second then on again. Removing the plug the relay continues to click on and off for a few cycles, which I don't think it did before.

      Left it a few months, then finally got round to taking the back off, and it worked as it should. So I tested various bits and all was well. Then turned it on again, and back to the clicking relay.

      I disconnected the main board from the power...
      02-06-2025, 08:42 AM
    • Loading...
    • No more items.
    Working...