Philips plasma FTP2.4A Vscan

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • The_Todd
    Senior Member
    • Jul 2017
    • 66
    • Australia
    #1

    Philips plasma FTP2.4A Vscan

    Hello guys,

    I got an old Philips plasma, I was hoping to revive this as i looove the ambient lights on the side,

    So it tries to start up, shuts down and blink on the front. The power supply gives a Vscan blinking errror, and goes into protection mode.

    When the Y board power supply plug is removed it starts fine, when the power plug is left in and the data flex cable removed it also starts fine.

    So where would the fault posibly lie? The power supply? The protection curcuit?
    The Y board? Or perhaps the mainboard is telling it to do somthing thats drawing too much current? Hmmm.....
    Tags: None
    • The_Todd
      Senior Member
      • Jul 2017
      • 66
      • Australia
      #2
      Re: Philips plasma FTP2.4A Vscan

      Oh also should mention, the unit is in unusually good condition, no leaking caps at all...anywhere. A bit dusty but other then then that almost perfect. And all voltages test out ok.

        Comment

        • dick_barton
          Badcaps Legend
          • Aug 2015
          • 6642
          • Wales
          #3
          Re: Philips plasma FTP2.4A Vscan

          I can't really help but what is the Vscan voltage and does it match what's given on the Plasma panel label?
          Willing to help but I'm no expert.

            Comment

            • The_Todd
              Senior Member
              • Jul 2017
              • 66
              • Australia
              #4
              Re: Philips plasma FTP2.4A Vscan

              Yup it does

                Comment

                • The_Todd
                  Senior Member
                  • Jul 2017
                  • 66
                  • Australia
                  #5
                  Re: Philips plasma FTP2.4A Vscan

                  Being as fast I can with the multimeter, it pulls about 265ma before shutting down, the power supply is only rated for 100ma. Hmmm..... Also the Y board has a fair bit of heat damage

                    Comment

                    • dick_barton
                      Badcaps Legend
                      • Aug 2015
                      • 6642
                      • Wales
                      #6
                      Re: Philips plasma FTP2.4A Vscan

                      Unplug the interconnections between boards and check the resistance of the various supply lines to ground. You may have a short circuit or a lower resistance than you should have on one of the supply lines.


                      Have you checked the Ybuffers for shorts. There are plenty of Youtube video's to guide you.

                      Post some clear pictures of your boards which can help.
                      Last edited by dick_barton; 09-21-2017, 07:23 AM.
                      Willing to help but I'm no expert.

                        Comment

                        • The_Todd
                          Senior Member
                          • Jul 2017
                          • 66
                          • Australia
                          #7
                          Re: Philips plasma FTP2.4A Vscan

                          Ok will soon, anyway there is progress found a stuffed capacitor on the y board, stopping the tranformer circuit from starting, so thats fixed......


                          NOW im getting the Vset error...ffs

                            Comment

                            • dick_barton
                              Badcaps Legend
                              • Aug 2015
                              • 6642
                              • Wales
                              #8
                              Re: Philips plasma FTP2.4A Vscan

                              Welcome to the wonderful world of servicing
                              Willing to help but I'm no expert.

                                Comment

                                • dskall
                                  Badcaps Legend
                                  • Oct 2016
                                  • 2905
                                  • usa
                                  #9
                                  Re: Philips plasma FTP2.4A Vscan

                                  Maybe some pictures of the board would help
                                  I assume no responsibility for any stupid suggestions I might post.

                                    Comment

                                    Previous template Next

                                    Related Topics

                                    Collapse
                                    • celiabrown
                                      Issue with Plasma Philips 37inch chassis FTL2.1
                                      by celiabrown
                                      Hello guys,
                                      My Plasma Philips 37inch chassis FTL2.1 does no picture ,and goes into protection mode after 30 seconds (red led blinks at 3Hz).


                                      Can someone has any symptom like this ?

                                      Thanks​
                                      05-09-2024, 10:56 PM
                                    • xrey
                                      Samsung Plasma PN58B860Y2F low vscan
                                      by xrey
                                      We all of the sudden started getting a washed out picture and rainbow colored static/snow.

                                      When we tested vscan, etc., everything measured properly but not the vscan.

                                      Supposed to be -193 got -93 (tested it w the TV on)

                                      Researched it and decided to replace the y board and y buffers.

                                      Now I get no picture or sound - TV turns on but nothing else.

                                      When I run the same tests I am still getting -93 on the vscan test and this is now a different Y board, buffers, etc.

                                      So I am thinking either I did something wrong originally in...
                                      10-18-2020, 11:21 AM
                                    • G33RT
                                      Philips 8200 series 65PUS8204/12 stuck at Philips Logo
                                      by G33RT
                                      Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.

                                      It does power up when pressing the power button.

                                      I already try the power button while plugin the plug with no result.
                                      Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.

                                      Could this be an PSU or eMMC issue ?
                                      07-19-2025, 03:43 AM
                                    • aidanmo
                                      Philips 43PUS7506/12 - Loud blown out sound
                                      by aidanmo
                                      Hello,

                                      I've got a really strange issue with the speakers on my Philips 43PUS7506/12. It makes this awful loud buzzing now. It happened after it was attempted to be wall mounted - I think the back got squeezed and something broke.
                                      I thought maybe the speakers got damaged, so I replaced them - no dice.
                                      • Using the internal speakers, it always happens.
                                      • Using the headphone jack, it never happens.
                                      • Using the digital/optical out with a soundbar - it happens after about 2h/movie runtime - it's never as drastic, it just pops in and out, but I didn't want it to damage the sound bar
                                      ...
                                      02-28-2025, 03:13 PM
                                    • ArMaaN376
                                      Samsung PS51E550 Plasma TV
                                      by ArMaaN376
                                      Hello,
                                      I am having Samsung PS51E550 Plasma TV. While the TV was working, a crackling sound heard & video went off with audio still ON. After switching it off & ON, the red LED on TV blinks six times & then off.
                                      Opened TV cover & observed foll
                                      a) Green LED on the small PCB blinks at @5-6sec ON & off for 3-4 secs. Red LED on logic board ON
                                      b)Vs & Va on power supply board raises momentarily to 209v & 58v resp & then drops.
                                      c) Cold test on Y-main board shows all 3 pins of FGPF4536 IGBT short to Grnd.
                                      How to confirm Y -Buffer board...
                                      06-19-2024, 04:05 AM
                                    • Loading...
                                    • No more items.
                                    Working...