Samsung UN40F6400 standby LED blink wont turn ON

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • mugunthans
    Member
    • Dec 2016
    • 32
    • Canada
    #1

    Samsung UN40F6400 standby LED blink wont turn ON

    Its time to get expert help to fix my TV as its almost dead !!!
    Its Samsung UN40F6400 and power board BN44-00622D

    The problem is - When power up the TV - standby LED blink twice for 5 Times and relay click but not ON and cycle continue...

    Based on advise from other thread on this forum and tested the below.

    1. Disconnected Main board cable 20Pins (CNM803)
    > LED backlight ON for half of the screen and half of screen flicker. Tear down the LCD panel and diffuser, found only top 3 Strip light UP and bottom 4 strips (2x2) flicker. So, removed the top 3 and swapped with bottom 4 LEDs but still top 3 is UP good and bottom same flicker.
    Hope the LED strips are found to be good - Please concure.

    2. Voltage measurement without Main board and LED panel connection

    Power supply @ CNM803
    OD On/Off - 3v
    B13V - 13v
    B5v - 5v
    DIM1,2,3,4 - 3V
    A5V- 5v
    BLU on/off - 5v
    Power On/off - 3v
    ++++++++++++++++++++++++
    LED Driver - Legend
    Ch 1-60v
    Ch 2,34 - 120v

    with/without LED
    CM851/CNM852 - 46v/67v
    CNM853 - 17v/35v
    +++++++++++++++++++++++
    Booster reading
    Measurement without LED panel connection
    Ch 1 - 70V (c9106)
    Ch 2,3,4 - 150v (c9206/c9306/c9406)
    Measurement with LED connection
    Ch 1 - 44V (c9106)
    Ch 2,3,4 - 85v (c9206/c9306/c9406)

    HOT Caps reading (with/without LED)
    CP810S - 305v / 396V
    CP814S - 305v / 396Vc
    +++++++++++++++++++++++
    anyone has schematics of BN44-0622D ?
    Tags: None
    • dskall
      Badcaps Legend
      • Oct 2016
      • 2905
      • usa
      #2
      Re: Samsung UN40F6400 standby LED blink wont turn ON

      You swapped 3 strips for 4. Did you swap forth strip?
      I assume no responsibility for any stupid suggestions I might post.

        Comment

        • mugunthans
          Member
          • Dec 2016
          • 32
          • Canada
          #3
          Re: Samsung UN40F6400 standby LED blink wont turn ON

          Originally posted by dskall
          You swapped 3 strips for 4. Did you swap forth strip?
          Yes, 4/5 - swapped with 1/2 and 6/7 swapped with 1/2 - same effect (1/2/3 constant light UP and rest flicker)- Hope LED strips should have no issue.
          Attached Files

            Comment

            • dskall
              Badcaps Legend
              • Oct 2016
              • 2905
              • usa
              #4
              Re: Samsung UN40F6400 standby LED blink wont turn ON

              Have you checked your connection between your strips and panel connector?
              I assume no responsibility for any stupid suggestions I might post.

                Comment

                • Hamie
                  Badcaps Legend
                  • Apr 2014
                  • 1383
                  • UK
                  #5
                  Re: Samsung UN40F6400 standby LED blink wont turn ON

                  http://www.ohmsupplies.co.uk/epages/...8&Locale=en_AU

                    Comment

                    • mugunthans
                      Member
                      • Dec 2016
                      • 32
                      • Canada
                      #6
                      [SOLVED] Re: Samsung UN40F6400 standby LED blink wont turn ON

                      Originally posted by mugunthans
                      Its time to get expert help to fix my TV as its almost dead !!!
                      Its Samsung UN40F6400 and power board BN44-00622D

                      The problem is - When power up the TV - standby LED blink twice for 5 Times and relay click but not ON and cycle continue...
                      I got some local expert advise..which is to replace SMD resister RS802 (10R0 - 10 Ohms) and Youtube channel also confirmed the same.

                      https://www.youtube.com/watch?v=nEzBdUTpe24&t=567s

                      but I could not source SMD...so I replaced it with normal Quarter watt resister...and Its working

                      Thank you very much for your valuable time and advise.

                        Comment

                        • budm
                          Badcaps Legend
                          • Feb 2010
                          • 40746
                          • USA
                          #7
                          Re: Samsung UN40F6400 standby LED blink wont turn ON

                          "HOT Caps reading (with/without LED)
                          CP810S - 305v / 396V
                          CP814S - 305v / 396Vc"

                          Something is not making sense since that resistor is for supplying the Voltage to run the PFC IC and your PFC Boosted Voltage is 396VDC as it should be, so I cannot see the relationship between one strip of LED is not working properly and that 10 Ohms resistor in the PFC circuit.
                          Or you are indicating that with LED connector in place and the one of the LED strip is not on you are getting 305VDc? I would expect that ALL LED strips will be affected wit 305VDC reading on the main filter cap and it also does not make sense to have 305VDC on the main filter cap when your AC line Voltage is 230VAC and the low Voltage shutdown should have kicked in too.
                          BTW, what is resistance reading of that BAD 10 Ohms resistor?
                          Last edited by budm; 07-10-2017, 12:03 PM.
                          Never stop learning
                          Basic LCD TV and Monitor troubleshooting guides.
                          http://www.badcaps.net/forum/showthr...956#post305956

                          Voltage Regulator (LDO) testing:
                          http://www.badcaps.net/forum/showthr...999#post300999

                          Inverter testing using old CFL:
                          http://www.badcaps.net/forum/showthr...er+testing+cfl

                          Tear down pictures : Hit the ">" Show Albums and stories" on the left side
                          http://s807.photobucket.com/user/budm/library/

                          TV Factory reset codes listing:
                          http://www.badcaps.net/forum/showthread.php?t=24809

                            Comment

                            • mugunthans
                              Member
                              • Dec 2016
                              • 32
                              • Canada
                              #8
                              Re: Samsung UN40F6400 standby LED blink wont turn ON

                              Not all the LED 7 strips failed...
                              First 3 is working constant full bright.
                              Next 2 flicker like flash and try to glow slowly and next 2 setup start flicker try to glow full bright and goes off last 4 dtrip...Same cycle repeat.
                              I have attached the photo in my previous post.
                              The resistor reading is (80ohms).
                              In fact i was waiting for your advice from my first post..
                              Special thanks to you...
                              Last edited by mugunthans; 07-10-2017, 12:13 PM.

                                Comment

                                • mugunthans
                                  Member
                                  • Dec 2016
                                  • 32
                                  • Canada
                                  #9
                                  Re: Samsung UN40F6400 standby LED blink wont turn ON

                                  Originally posted by mugunthans
                                  The resistor reading is (80ohms).
                                  My Apologies...Its 580Ω

                                    Comment

                                    Previous template Next

                                    Related Topics

                                    Collapse
                                    • Document Archive
                                      Samsung Galaxy Book 2 Notebook Specification for Upgrade or Repair
                                      by Document Archive
                                      This specification for the Samsung Galaxy Book 2 Notebook can be useful for upgrading or repairing a laptop that is not working. As a community we are working through our specifications to add valuable data like the Galaxy Book 2 boardview and Galaxy Book 2 schematic. Our users have donated over 1 million documents which are being added to the site. This page will be updated soon with additional information. Alternatively you can request additional help from our users directly on the relevant badcaps forum. Please note that we offer no warranties that any specification, datasheet, or download...
                                      09-07-2024, 05:50 AM
                                    • fixit007
                                      Samsung flicker - BN44-00932T board or else?
                                      by fixit007
                                      I picked up this TV that the prior owner said - just died.

                                      Tested the fuse - burnt. A dead capacitor is visible too on the hot side (CP801). Got the replacement power board (cheaply - used). Replaced the board - the TV turned ON!

                                      Now, about a month later (yesterday) I noticed the left side of the screen was flickering from time to time. That was already happening with the antenna input, not through HDMI.

                                      Also, some glitchiness with a Fire stick on HDMI3 - I hit an app with quick dark screen in stick, the TV goes - no input. Then I had to choose the stick...
                                      05-04-2024, 06:14 PM
                                    • tvguy12012012120
                                      Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
                                      by tvguy12012012120
                                      This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

                                      Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
                                      02-07-2025, 05:13 PM
                                    • ChristianBr01
                                      LED TV Samsung The Frame 55 inch QE55LS03RAU Standby Light only
                                      by ChristianBr01
                                      Hello everyone,
                                      I got a Samsung The Frame 55 inch TV for free from uncle cause it is not turning on anymore. I am in the second year of training as an electrician so I have knowledge already but I am far away from to be a pro.
                                      The TV has Standby but ist not turning on. A Friend of mine owns a 50 inch Frame TV so I checked the One Connect Box and the One Connect Cable there. Both are good and working normally. I have opened the TV case and measured some voltages on the Board.
                                      What I already found is that the 12.8V are not an the connector to the main board connector to the power...
                                      04-23-2025, 01:48 AM
                                    • Kaar3l
                                      Samsung QLED QE65Q7FNAT only standby light
                                      by Kaar3l
                                      TV: Samsung QLED QE65Q7FNAT
                                      PSU: BN4400940A
                                      MB: BN94-12832K

                                      I got the tv in spring 2024. At that time it started, then ran 60 sec and poweroff. Seemed like reboot issue. I didn't have time and room to check it in summer so I plugged it in and now the standby light is on. I press button on remote, standby light goes off and tries to start?. No picture or backlight on LCD. I thought about removing diodes like in this thread: https://www.badcaps.net/forum/troubl...sung-qled-q60r...
                                      09-24-2024, 01:35 PM
                                    • Loading...
                                    • No more items.
                                    Working...