Panasonic TH50U30A

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • chrismurphy
    Badcaps Veteran
    • May 2014
    • 251
    • australia
    #1

    Panasonic TH50U30A

    Repaired this tv with new SD and SU boards and was all good ,and eventually sold it
    2 months later the set is turning off after 15 mins , leaving only a green light on the front panel ,no blinks , and no response from the remote
    anyway turning off at the mains and then on works again , but shuts down again 5 to 15 mins later
    Reduced the Vsus voltage from 215 to 210 seems to have fixed the issue
    Can anyone tell me the correct Vsus voltage for this TV as there is no sticker on the panel
    Tags: None
    • tw2005
      Badcaps Legend
      • Oct 2011
      • 6458
      • Australia
      #2
      Re: Panasonic TH50U30A

      Originally posted by chrismurphy
      Repaired this tv with new SD and SU boards and was all good ,and eventually sold it
      2 months later the set is turning off after 15 mins , leaving only a green light on the front panel ,no blinks , and no response from the remote
      anyway turning off at the mains and then on works again , but shuts down again 5 to 15 mins later
      Reduced the Vsus voltage from 215 to 210 seems to have fixed the issue
      Can anyone tell me the correct Vsus voltage for this TV as there is no sticker on the panel
      Vsus Lo = 215V. Strange fault , have not seen that.

        Comment

        • ReeceyBurger123
          Never Give Up !
          • May 2014
          • 7325
          • Britain
          #3
          Re: Panasonic TH50U30A

          Check for cold solder joints on the sus fets and bad grounds that can also cause that.
          Please Do Not PM My Page Asking For Help Badcaps Is The Place For Advise, Page Linked For Business Reasons Only. Anyone Doing So Will Be Banned Instantly !

          https://www.facebook.com/Telford-Tel...7894576335359/

            Comment

            Previous template Next

            Related Topics

            Collapse
            • Buzztv
              Panasonic TC-P42S60 Plasma,how to check Vsus
              by Buzztv
              Hi,
              This is my first post in attempting to keep my beloved 2013 Panasonic plasma tv going.
              About 6 weeks ago the tv was turned on but then immediately shut off. There was no recent power surge or popping noise or any other symptom.
              I checked all of the obvious things and decided to try a replacement power supply board (PSS in Panasonic lingo).
              I would like to check the Vsus but this is one of the final models and at that point Panasonic did not indicate the Vsus and Vad voltages inside the chassis. It looks like they were discouraging people from making adjustments....
              10-27-2019, 01:24 PM
            • Amraks
              Panasonic SA-MAX770 (not turning on)
              by Amraks
              Hey all its been awhile since I have needed to post here.

              Panasonic - SA-MAX770: Symptoms not turning on

              Power Supply
              C1403 has 330v

              IC1402 Looks perfectly fine no blown out holes.

              C1601 has 3.3v


              CN1851 Has its 3.3v but no 15v all I am getting is on the 14v rail is 0.400v

              Not sure where I should be looking next for this any help would be appreciated...
              10-04-2022, 12:12 AM
            • Andre Gilbert
              Panasonic TC-P55ST50 8 blinks then no blinks
              by Andre Gilbert
              Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing here🤔?
              Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting 😂.

              TV Model: Panasonic TC-P55ST50
              ...
              1 Photo
              11-20-2024, 08:52 PM
            • AquaMan Ua
              Problem with PANASONIC CF53 laptop after changing BIOS settings
              by AquaMan Ua
              Hello. I am asking you for a hint on how to solve the problem with my touchbook Panasonic CF53-2 standart model. After setting up the BIOS, the laptop displays the wrong image until Windows loads. (More precisely, it displays, but distorted, instead of the Panasonic image immediately after turning it on, it displays what is in photo #1 in the attached file) Then the image appears when Windows starts loading and then there are no problems with the screen until the reboot. If you enter the BIOS, just a black screen. If you connect an external screen, the image on it is the same as on the built-in...
              2
              2 Photos
              05-17-2025, 09:40 AM
            • aa10aa10
              Panasonic Toughbook CF-33 mk1 BIOS repair
              by aa10aa10
              Good day,

              I have tried to remove BIOS supervisor password from Panasonic Toughbook CF-33 mk1. Model number CF-33AENABTG, unfortunately I don't have any other info.

              I read the BIOS using afuwin, edited it and tried to flash new edited BIOS using afuwin. Unsuccessfully. Afuwin showed "Error: Problem erasing flash." starting with 0x00040000 and stoped. Then I tried many other options to flash BIOS from Windows without any luck. Finally i rebooted the device - and no post. Afterwards I have read the corrupted bios chip (MX25L12873F) using EZP2010 programmer....
              01-21-2025, 06:13 AM
            • Loading...
            • No more items.
            Working...