Power Supply MEGMEET MLT668TL-VM

nataf10

Member

Join Date: Mar 2012

Posts: 37

Country: Israel
#1

Power Supply MEGMEET MLT668TL-VM

10-26-2016, 02:34 PM

Hi to all
Need help with this power supply.
TV turn on when first time put power cord into wall outlet.
When the TV was in STBY, the red LED turn green but the TV is off.
I checked the power and found that the 5Vstby is ok and when turn on the TV the power control pin increase from zero to 3.5v. The 12v and 24v are not providing any voltage.
Only when pull out from wall outlet for a few hours TV will turn on again
Please help
Thx

Last edited by nataf10; 10-26-2016, 02:39 PM.
Tags: None
vinceroger69

Badcaps Legend

Join Date: Mar 2012

Posts: 6714

Country: uk
#2

10-26-2016, 02:39 PM

Re: Power Supply MEGMEET MLT668TL-VM

https://www.badcaps.net/forum/showth...light=MLT668TL
Comment

Previous template Next

Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?

by Tynan Dill

I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

Upon bringing it home and plugging it up, it showed a standby light.

I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

The screen seems to blackout and stay black, but with a flashlight I can see the display.

With my Playstation 4 connected via HDMI, and running a game I can hear sound.

Assuming...

7 Photos
- Channel: Troubleshooting TVs and Video Sources
11-22-2024, 01:46 PM
Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply

by sam_sam_sam

I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
- Channel: General Electronics Technical Discussion
03-31-2024, 02:12 PM
Russound CA4 Power Supply Repair

by CMCM

Hello Everybody,

Trying to repair a power supply from a Russound CA4 Multizone Controller (picture attached)

Russound no longer supports it but were kind enough to provide a schematic of the power supply (pdf attached).

The outputs marked 12v and 20v are all measuring only 1v.

The board is clicking, which I think means it is in something called hiccup mode when the flyback transformers switches because of an internal problem or something else on the board Overloading it.

The capacitors physically look clean (no bludgesor leaks) and...
- Channel: Troubleshooting Power Supplies and Power Supply Design
07-03-2025, 01:12 PM
Mid 2014 A1398 MacBookPro,Is it feasible to remove the battery from the MBP and connect it to an external power supply?

by Gust zhang

I have a 15 - inch Retina MacBook Pro from the mid - 2014 model. Here is the link: https://www.badcaps.net/forum/showth...light=820-3662 . The battery broke some time ago. After I removed the battery and plugged in the original power adapter, the MBP could boot up normally. However, when I checked with IntelPowerGadget, I found that the CPU speed was limited to 0.8 GHz, and it ran very slowly. Later, I found a solution on GitHub. There is an open - source project called cputune that can set the CPU running speed. So I can now run the MBP at full speed. But another problem...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
02-16-2025, 08:39 AM
Power supply Manson NTP-5561 (5661) LCD controller dead - PIC18F87K90 HEX dump required

by Andreas_de

Hello!

i got a damaged Manson NTP-5561 (60V, 1,6A DC output) and and the main issue is that the controler IC for the LCD display has a short. The controler IC PIC18F87K90 is mounted on the back of the back of the LCD. Vss-Vdd = 3 Ohm. The 5V and 3,3V power line was killed as well, but that is not a problem. A new LDO 3,3V and 5V 7805 is already ordered.
Replacing the PIC18F87K90 is necessary but that makes no sense without having the HEX dump of the new controler.

Does anybody have such a power supply and could do a HEX dump of the Flash and EEPROM memory?
...

2 Photos
- Channel: Troubleshooting Power Supplies and Power Supply Design
04-12-2025, 10:38 AM
Loading...
No more items.

Power Supply MEGMEET MLT668TL-VM

Power Supply MEGMEET MLT668TL-VM

Comment

Related Topics