TCP60ST50 7 blibking red lights

Collapse
X
Collapse
 
  • Page of 6
  • Time
  • Show
Clear All
new posts
Previous 1 2 3 4 5 6 template Next
  • JSJohn
    Senior Member
    • Aug 2016
    • 60
    • USA
    #101
    Re: TCP60ST50 7 blibking red lights

    Thanks!!! I definitely owe you several

    Of course, I trusted ya. Your advice made perfect sense regarding the wrong diagnosis with a bad board.

    I have put the cover back on with 4 screws as you suggested. Gotta protect those new boards. HA HA HA!

    Placing a order for the new screws and will definitely take care while installing them.

    Thanks again. I hope someone learns from my pitfalls. I look forward to contributing and gaining more insights.

      Comment

      Previous 1 2 3 4 5 6 template Next

      Related Topics

      Collapse
      • SMDFlea
        ME Firmware Cleaning Guide
        by SMDFlea
        Here`s a quick ME Firmware cleaning guide.

        The guide is basic,its main goal is to show you how to use intel FIT,its highly recommended that you all follow the guide posted at win-raid

        (The attached FIT version is 11, if your ME Firmware (FW) is not 11.0.*.* follow the win-raid guide. Use the tools version for your ME FW, for example: ME System Tools v9.1 For systems running ME v9.0 - v9.1)


        A video,software (intel FIT) and practice bios are all included. I`ll post a better video and more advanced guide at a later date.


        1. Open the...
        09-09-2020, 09:10 AM
      • Francesc V.
        Christmas lights - Something I am doing wrong
        by Francesc V.
        Hi:

        i am trying to repair this Christmas lights from my parents. They are incandescent lights, no led lights.

        I have tried with 12V a 24V small lights that I found in Aliexpress but is obvious that are not the right ones. They last microseconds connected. Do they blow because of Amps or Volts?

        If I measure the Amps in the string........it's only 90mA. If I measure the Volts in the "green box"......it's between 0 and 190V, but doing a little bit of maths from the number of bulbs in series.......it's only about 6V per lamp.

        Could...
        03-11-2023, 07:38 AM
      • bialag
        Lenovo ThinkPad E14 Gen 5 - Not Powering On - 3 Blinking Lights - 20 volts 0.224 amps
        by bialag
        Hello,

        I have a Lenovo here that does not want to power on. The motherboard appears to be clean, no sign of corrosion or obvious fried components. When plugged in, I see 3 blinking lights and then off. It would cycle the 3 blinking lights every 10 seconds or so as long as I have the adapter plugged in. Amp meter shows 20 volts, 0.224 amps, no fan spin, red light indicator near the charge port.

        Thermal camera shows a section of the motherboard that is warmer than the rest. It is near the connector labels JRTC1 (CMOS battery). Diode measurement to ground for pin 1 = OL,...
        03-25-2025, 05:56 PM
      • acedogblast
        Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
        by acedogblast
        This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

        There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
        11-02-2024, 05:13 PM
      • gabrielA7
        IMAC A1418 / MB: 820-00430-a / does not turn on, Lights 3 of the 4 LEDs and turns off.
        by gabrielA7
        Does not turn on, lights 3 of the 4 LEDs and turns off and stays like this, presses the power and repeats.
        I saw that the room LED lights up only when the screen is connected, so quiet.

        We have all the power supplies, even processor, 1.8V
        One thing I found strange, it has a very low resistance in the Vcore is giving 1 Ohm , work with notes and such, I know that this is normal in some processors but with this resistance only take video card so found it strange.

        I suspect that there may be some leak in the processor.
        Anyway, when I press the power, it...
        10-29-2024, 06:48 AM
      • Loading...
      • No more items.
      Working...