Re: LG 37LC55 Flickering and then stand by
I get 'Access denied' for this links at shopjimmy.com
I get 'Access denied' for this links at shopjimmy.com
-
-
Re: LG 37LC55 Flickering and then stand by
I get 'Access Denied' for this links...
but in the board the PCB model is :
EAX32268301/8
06.12.12 Rev 1.0Comment
-
Re: LG 37LC55 Flickering and then stand by
im not sure where you live country wise but the uk and a few other places have been blocked by shop jimmy you need too use a web proxy to view the links.Last edited by vinceroger69; 03-23-2016, 12:54 PM.Comment
-
Re: LG 37LC55 Flickering and then stand by
EAX32268301 is the blank PCB P/N which can be stuffed with different components to create many PCB assemblies (PCBA).
I believe your PCBA is EAY34796801 as marked in pink as shown by pix from SJ.
Pictures provided by Shopjimmy.Attached FilesNever stop learning
Basic LCD TV and Monitor troubleshooting guides.
http://www.badcaps.net/forum/showthr...956#post305956
Voltage Regulator (LDO) testing:
http://www.badcaps.net/forum/showthr...999#post300999
Inverter testing using old CFL:
http://www.badcaps.net/forum/showthr...er+testing+cfl
Tear down pictures : Hit the ">" Show Albums and stories" on the left side
http://s807.photobucket.com/user/budm/library/
TV Factory reset codes listing:
http://www.badcaps.net/forum/showthread.php?t=24809Comment
-
-
Re: LG 37LC55 Flickering and then stand by
Yes, is the same number as in your picture, the one you wrote.Comment
-
Re: LG 37LC55 Flickering and then stand by
And now , what is the next step?Comment
-
Re: LG 37LC55 Flickering and then stand by
This link should be the correct service manual for your tv it may tell you how to force on the psu for tests etc
Comment
-
Hello everyone!
Tonight I picked up a Samsung UN65NU6900FXZA with a curious issue.
Symptoms:
1) Plug TV in to AC outlet, stand-by light illuminates briefly and goes out.
2) TV does not appear to turn on
3) Backlights do not illuminate, voltages associated with backlights on Power Supply are not present
4) "Power on" terminal on Power Supply has 3.26v
5) "A13V" terminals have 12.9v
6) Stand-by test jumper on Power Supply has 12.9V
7) Optical audio jack on Main Board illuminates
8) With stand-by... -
Hello,
The monitor started off showing flickering thin (1 pixel) lines horizontally every say 3mm..
They are black on the right and gradually fade to nothing on the far left.
They start either after 5 mins or up to 2 hours after so annoying for testing.
They flicker continuously very fast! With a slight pause milli-second every second.
Initially I cleaned the LVDS cable and connected to the T-Con and then it worked fine for 3 weeks but not sure if this was just co-incidence.
I tested each half by removing the first the left flex from... -
This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.
Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today.... -
Hi. I got a Vizio with no power or standby, and won't turn on with remote or button. I checked the voltages on the connector and all read 0.00V or nearly 0(0.050 ON/OFF pin). None of the pins are labeled STB for standby although I do see some 5V pins. Other than the obvious standby led, which isn't coming on, is there a way to check for standby voltage on this PS. I'm trying to see if my problem is the PS or mainboard. Some Vizios I have fixed with no standby led me to think it was the PS but it turned out being the mainboard. Any experience with this set would be greatly appreciated. -
Hi all.
I started a thread while back regarding TV power supply standby circuitry as it is something I am not quite on top of.
SMPS theory and function is becoming more familiar, however the standby part is still a bit of a mystery.
Anyway, a friend has this TV with the above mentioned power supply board which has no standby voltage, nor any other voltages leaving the board.
The mains AC comes in fine, gets filtered and rectified with power is on the main filter cap as well as the transformer and drain pins of the ICE3B0665J, but that's it.
...
Comment