Lg 50pg20 cable connector question

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • crdz66
    Badcaps Veteran
    • Nov 2012
    • 242
    • USA
    #1

    Lg 50pg20 cable connector question

    Hello everyone.

    I have a plasma tv lg 50pg20 with white distortion on bottom of the screen.

    Like year ago, i replace the upper buffer board, but i forget to put back the little cable connector between upper and lower buffers boards.

    I check the bottom buffer board and looks ok for me.
    No shorts, good resistance readings.

    So, do you think that this missing connector make tv fail sometimes??

    Thanks
    Tags: None
    Previous template Next

    Related Topics

    Collapse
    • howardc64
      A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
      by howardc64
      Problem

      This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
      08-04-2024, 10:36 PM
    • howardc64
      TCL 55S425 few horizontal lines, potential failure on both side of panel/buffer board
      by howardc64
      All left and right refers to looking from rear of TV (or looking from front with TV upside down)
      • TV came with vertical bars and no image. Found faulty TVS on left buffer board. Also replaced T-Con (may have damaged the original while hot air removing components, board has slight warp) and have full image but few horizontal lines on the screen. Some of the lines appears to be 2 pixel tall while others are 1 pixel tall.
      • Disconnecting left and right buffer board potentially reveals problems on both sides with different signals (unless this T-Con require jumper like Samsung FB_TRDY1&3) Fault
      ...
      07-24-2025, 05:17 PM
    • Tomylee
      No LCD image after connector replacement – lifted components and damaged resistor (Nintendo Switch Lite HDH-CPU-02)
      by Tomylee
      Hi everyone,

      Sorry for the person who’s going to read all this !
      I'm on a Nintendo Switch Lite, motherboard HDH-CPU-02.

      While replacing the left joystick, I had to remove the motherboard to access the connector underneath. When I lifted the LCD connector latch, it broke (the plastic had become brittle over time), so I replaced the entire connector.

      During the desoldering of the LCD connector using hot air, three small components located just below the connector (likely 0402 capacitors) came off and remained stuck to the bottom of the...
      07-11-2025, 11:52 AM
    • Tynan Dill
      Vizio e601i-A3 - Has Sound and Display, But No Backlight - Bad Power Supply Board or Bad LED Bulbs ?
      by Tynan Dill
      I was given this TV from my great uncle. He said it just wouldn't turn on one day out of nowhere, replaced the TV, and gave it to me to possibly fix and use for myself.

      Upon bringing it home and plugging it up, it showed a standby light.

      I powered it on and without a flashlight, the display showed the "V" but the lighting is very dim, but visible.

      The screen seems to blackout and stay black, but with a flashlight I can see the display.

      With my Playstation 4 connected via HDMI, and running a game I can hear sound.

      Assuming...
      ORIGINAL POWER SUPPLY BOARD
      7 Photos
      11-22-2024, 01:46 PM
    • spleenharvester
      Whirlpool PACF212HP W portable air conditioner, upper fan only turns slowly.
      by spleenharvester
      I just acquired this portable aircon, history unknown. Its behaviour is quite strange:
      • When turned on and placed into cooling mode, the upper fan (cold air out) just spins slowly. The compressor and lower fan do not run.
      • If the device is then placed into heating mode and then back into cooling mode, the lower fan and compressor kick in and start cooling, but the upper fan still only spins slowly.
      • If the device is placed into fan-only mode, the upper fan does not respond to low/medium/high speed toggles - just keeps running slowly.
      • Display and buttons all behave normally aside from the
      ...
      06-27-2025, 07:49 PM
    • Loading...
    • No more items.
    Working...