Sony KLV-40BX400 blinking red 6 times

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • playgoods
    Member
    • Jan 2014
    • 18
    • South Africa

    #1

    Sony KLV-40BX400 blinking red 6 times

    I'm repairing a Sony KLV-40BX400 LCD TV.
    When I switch it on the standby light will go green and I'll get the sony logo. It will then immediately flash green and then I'll get the sony logo again. It will do this 3 times and then the red standby led will flash 6 times.

    I've read that it can be an over voltage. I've measured the inverter 24 supply from the PSU and it's at 25.6V can this be the cause?
  • martyparish
    Badcaps Veteran
    • Dec 2012
    • 313
    • United States

    #2
    Re: Sony KLV-40BX400 blinking red 6 times

    Link to service manual:



    6 blinks is inverter error. Pictures would help you get more response. Especially a closeup of inverter.

    Comment

    Related Topics

    Collapse

    • YasaCh
      Sony kdl 40p5500 red light keeps blinking 3 times
      by YasaCh
      Hello...
      my tv almost 2 years not powerd on and when i turned it on nothing happened and only 3 red light keeps blinking
      i opened the back cover no sign of damage on the powery suply or motherboard
      when i plug in the power i hear the reley sound like tik first and another tik..after that only red keep blinking..
      another thing is even after i unplugged the power, The tv keeps red blinking 3 times for 2 almost 2 munites
      07-07-2025, 11:53 AM
    • NolesFan
      Sony kd-85x85j LED blinking red 6 times
      by NolesFan
      I know the 6 blinks are a backlighting issue, but when I pulled off the back cover and turn it on, the is a white flash from with the panel then I hear what sounds like a relay trip and the TV goes into the 6 blinking light code. Before I pull all the electronics off and checking the individual strips, there is a on the power board, a harness with 4 wires that run thru the panel, which are what I believe are the LED lines, but Im not a tech so no clue. Wires read OUT 1 + & - and OUT 2 + & - My first inclination was to remove the power board and use my LED tester and go to each + &...
      03-16-2025, 11:50 AM
    • androripara
      Sony Bravia 55HX820 - 4 times blinking red standby led
      by androripara
      Hello everyone,
      i am trying to repair a Sony KDL-55HX820 led TV which is throwing error code 4 (standby led flashing four times).

      I followed the troubleshooting flowchart at page 69, and between pin1 and pin7 of CN6002 i am reading 1.91V so i guess i can rule out the B Board as the culprit.
      Before ordering new G* Boards (by the way, should i change both? it is not specified in the manual) i wanted to try and do more advanced troubleshooting since i've read in other threads people resolving their problems on the 46/55 HX 820/823/825 models by replacing the Samsung led...
      10-19-2023, 05:16 AM
    • ahmarzo
      Hp 15-cs laptop 5 times dc jack blinking white
      by ahmarzo
      I have two laptop hp15- cs1000tx with motherboard part no DAG7BDMB8F0 REV F

      First one was not powering on when battery is connected the first n channel MOSFET was short and after changing the laptop started on power and battery and charging fine

      Second laptop has water damaged on ram ic after cleaning and changing the ic the laptop is working fine now

      But now I have power led continuously blinking 5 times in both the laptop even after shutdown and when it is powered on the led keeps blinking 5 times .both the laptop is charging and working on both battery...
      12-28-2024, 04:46 AM
    • mauda
      Sony TV model KD-65XE7005 - only Sony logo for 3 seconds
      by mauda
      I'm currently working on repairing a malfunctioning Sony TV model KD-65XE7005 with the mainboard 1-981-926-21. I would appreciate your assistance with this issue.

      Upon powering on the TV, the Sony logo appears for approximately 3 seconds, after which the backlight remains lit, the screen remains black, and nothing else happens. The TV consumes around 55W initially and then drops to 35W. The indicator LED remains solid white. It doesn't respond to the remote control. When attempting to update the TV using a USB dongle, the dongle briefly flashes but nothing else happens.
      ...
      05-21-2023, 11:56 PM
    • Loading...
    • No more items.
    Working...