Panasonic tc-p55gt30

[Malachi]

Re: Panasonic tc-p55gt30

Did you see I amended my results from before? I had the VFo and the vf5f switched.

[Malachi]

Re: Panasonic tc-p55gt30

Double post sorry. Internet is acting up here.

[tw2005]

Re: Panasonic tc-p55gt30

Did you see I amended my results from before? I had the VFo and the vf5f switched.

Did you see I amended my results earlier. I had the VFo and vfv5 switched.

Vf5v 13.42 the first time and 13.31 the second time.
Vscn_f 0.L
VFo 0.L

Lower board:
vf5v 8.92 the first test, 8.98 the second
0.L the rest.

OL generally means out of range so i can only interpret that as greater than 60Mohms since the claimed range of this meter is 60 Mohms.

All I can say is if they're that high then it won't blow the SC , and they may be fine. I've seen this before on earlier models where the resistances are high, nothing like what I get and they've been fine.

I am surprised though you can't get the 29Kohms though.

I can't say much more. I'd love to give you 100% assurance, I can't. It will still be a bit of a gamble but if the SC you get is fine, you could always resell or keep looking for another 55" one to pop up.

I'd have a go.

Comes down how much risk you can handle. The boards of value in these would be primarily SC,SU,SD, A-board, panel.

[Malachi]

Re: Panasonic tc-p55gt30

Ok, thanks for your help. Sorry for being so ignorant about this stuff.
I make teeth for a living. Lol.

[tw2005]

Re: Panasonic tc-p55gt30

Ok, thanks for your help. Sorry for being so ignorant about this stuff.
I make teeth for a living. Lol.

Cool, I'll add you to my contact list then as I'm sure mine will be wear out.

I'm sure you'll get there. Just repaired 2 SC boards for my GT, parts arrived Running it in now to see if it goes poof again

[gdawg]

Re: Panasonic tc-p55gt30

Did you order a kit from SJ or just the fet's by themselves. I am curious cause SJ usually includes ic's and a bunch of stuff I usually don't replace. I am waiting for a kit right now for my 55gt31. I had a question related to this post. I have a SU board that has one shorted chip. I removed the chip and the short went away. If I put that board in with out the chip, will the tv fire up. I know I would be missing the drive for the panel but don't want to harm anything. I was going to order a chip and try my luck on soldering it in, so I thought if the rest of the buffer works I would proceed, otherwise I would be looking for one of those hard to find 5340 buffers.

[Malachi]

Re: Panasonic tc-p55gt30

I ordered the whole sc board.

[gdawg]

Re: Panasonic tc-p55gt30

Sorry, I should have directed my question to tw2005. Make sure you get some guidance before just putting the board in, cause you can fry it. I know this from bad luck I've had. I think you originally said you had a 8 blink code, but I think that was cause nothing was plugged into the power supply.

[Malachi]

Re: Panasonic tc-p55gt30

I don't know what else to test. When the board gets in, I'll ask for any final instructions before the delicate operation. Lol

[gdawg]

Re: Panasonic tc-p55gt30

When you get the board, make sure you screw it down using the ones with lock washers. You might have to pull one off the other board and go down to the local hardware store or sometimes you can buy them thru ShopJimmy. Just put in Panasonic screws and you should see results. Once its screwed down, make sure the ribbon cable is plugged in to the sc20 connector and your power lead is plugged in. You will need to locate a connector on the SC board marked sc50. Its located lower left close to the lower buffer board. It has two pins in it which you have to jump with an alligator clip or anything that will short the two pins together. Make sure the buffers are totally disconnected. When you power it up, hopefully the tv will stay on with no codes. Of course you wont have a display but the tv should stay on. Only let it run for less than 30 seconds. If there is a problem it will show up right away and blink a code. Both the SC and the SS board will have led's that light when power is on. If that works then you need to remove the jumper at sc50 and install the buffers. And with fingers crossed , toes crossed you should have a working tv.

[gdawg]

Re: Panasonic tc-p55gt30

You may also look at the back of the panel where the SC board mounts. You will see small bumps with holes in them to screw it down. Make sure the bumps have no black marks around them as that is usually what does in the SC board. I use a little sand paper to take off the black marks. I can almost guaranty they will be there. Make sure to tighten the screws on the SS board or replace them with the new screws.

[Malachi]

Re: Panasonic tc-p55gt30

I will have to get alligator clips.
Thanks for those instructions.
I'm hoping that the previous owner figured out the Sc board was bad and took it out, then for whatever reason decided it cost to much to get a replacement or to have it rebuilt and sold the tv as working and disappeared.
Seems like these sc boards fail often?

[gdawg]

Re: Panasonic tc-p55gt30

Yep, that is a common failure along with the upper buffer. Some of the models had the same issue with the SS board, but it didn't involve the buffers. If I send you my teeth size, can you send me some?? lol. My wife asked me, "so how many teeth do you still have" instead of asking how many are you missing. Pretty harsh!!

[gdawg]

Re: Panasonic tc-p55gt30

Forgot to tell you. Tw2005 hopefully will read this and I hope I explained everything so you dont get in trouble. Always remember when the tv is powered on, there are lethal voltages so just be careful not to stick your fingers anywhere on the board. Those large caps hold a lot of voltage even with the tv off. So be careful handling boards after they have been powered up. I got my finger around the corner when I was removing it and my arms were numb for about 15 minutes. Dont want to scare you, but just be carefull.

[Malachi]

Re: Panasonic tc-p55gt30

Trust me I'm very scared of that. I've got to melted spots on my analog meter leads.
Couldn't see for 5 minutes from the sparks.

[Moreno83]

Re: Panasonic tc-p55gt30

Hahaha!

Happened to me to when i first started repairing tv's!

[Malachi]

Re: Panasonic tc-p55gt30

Well I guess I won't be getting the board.
The company that sold it to me on eBay asked my to call him.
He said he has repaired a lot of those tv's and he believes the problem is a bad plasma panel.
That whoever had it took the sc board out because it's the most sought after one and probably sold it then sold the tv to the 70 year old I got it from, who was told it was working.
The eBay seller refunded me the money.

I'm bummed out now. Lol

[Moreno83]

Re: Panasonic tc-p55gt30

So this tv originally came from that repair guy?

In my opinion , if you have a bad panel then you also have shorted buffer boards. Buffer boards were ok right?

[Malachi]

Re: Panasonic tc-p55gt30

No. The TV came from a free online selling and buying sight called Craigslist.
From the directions I followed tw2005 seemed to think the buffer boards were ok.

[Moreno83]

Re: Panasonic tc-p55gt30

Then i don't get it why that guy says the panel is bad. If you don't have shorted bufferboards then chances are high that the panel is fine. Im not that experienced with repairing plasma tv's so i can't give you a 100% answer. Started repairing like 1.5 years ago.

However. I once tried to repair a plasma tv which had shorted buffer boards. Bought new bufferboards , tested them for shorts BEFORE installing them and they were fine. Installed them , connected all cables and again the new bufferboards were shorted ----> bad panel!

Try and find a working SC board and install it. Use the SC50 jumper to test the board without using the bufferboards. Worst case scenario you end up with another bad SC board which you can sell for at least $50 as its a wanted board......