Using bulb to test X main after IGBT/Gate driver IC replacement

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tech2014
    Badcaps Veteran
    • Aug 2014
    • 807
    • Canada

    #1

    Using bulb to test X main after IGBT/Gate driver IC replacement

    I have a Samsung plasma TV that keeps clicking at power up. I found VS measured shorted on the X Main. I found it had 4 shorted IGBTs. I replaced all of them and also plan on replacing all of the gate driver ICs, FAN73611 and FAN73711. After replacing the gate driver IC, I want to somehow test the board with a bulb to make sure I didn't miss anything.

    How would I go about doing this?
  • Alastair E
    Chief Womble
    • Mar 2013
    • 1963
    • U.K.

    #2
    Re: Using bulb to test X main after IGBT/Gate driver IC replacement

    Disconnect the Vs supply Only from the Y-SUS/X-SUS, then wire a 100-150W 240V bulb in series from Vs plug on the PSU to Vs point on Y-SUS/X-SUS--Whichever you're testing/protecting....
    Last edited by Alastair E; 02-19-2016, 02:15 AM.
    TELEFIX

    How PLASMA SCREENS WORK, X-SUS and Y-SUS what they do--
    http://www.irf.com/technical-info/appnotes/an-1088.pdf
    PLEASE DO NOT EMAIL ME PRIVATELY FOR REPAIR ADVICE. QUESTIONS BELONG ON THE FORUM!

    Comment

    • tech2014
      Badcaps Veteran
      • Aug 2014
      • 807
      • Canada

      #3
      Re: Using bulb to test X main after IGBT/Gate driver IC replacement

      ok, how do you wire the bulb?

      Comment

      • Alastair E
        Chief Womble
        • Mar 2013
        • 1963
        • U.K.

        #4
        Re: Using bulb to test X main after IGBT/Gate driver IC replacement

        Youve replaced IGBT's, Driver-chips etc etc.....

        And you're asking HOW TO WIRE A BULB!!

        Sheesh!!
        TELEFIX

        How PLASMA SCREENS WORK, X-SUS and Y-SUS what they do--
        http://www.irf.com/technical-info/appnotes/an-1088.pdf
        PLEASE DO NOT EMAIL ME PRIVATELY FOR REPAIR ADVICE. QUESTIONS BELONG ON THE FORUM!

        Comment

        • tech2014
          Badcaps Veteran
          • Aug 2014
          • 807
          • Canada

          #5
          Re: Using bulb to test X main after IGBT/Gate driver IC replacement

          never done it or know anyone who has. bulbs don't come with wires.

          Comment

          • Alastair E
            Chief Womble
            • Mar 2013
            • 1963
            • U.K.

            #6
            Re: Using bulb to test X main after IGBT/Gate driver IC replacement

            Oh good grief....

            Batteries dont come with leads--But you manage with those!

            Thats what Soldering-Irons are for!
            TELEFIX

            How PLASMA SCREENS WORK, X-SUS and Y-SUS what they do--
            http://www.irf.com/technical-info/appnotes/an-1088.pdf
            PLEASE DO NOT EMAIL ME PRIVATELY FOR REPAIR ADVICE. QUESTIONS BELONG ON THE FORUM!

            Comment

            • vinceroger69
              Badcaps Legend
              • Mar 2012
              • 6714
              • uk

              #7
              Re: Using bulb to test X main after IGBT/Gate driver IC replacement

              i just use a bulb holder for the bulb and then connect that way.

              Comment

              • tech2014
                Badcaps Veteran
                • Aug 2014
                • 807
                • Canada

                #8
                Re: Using bulb to test X main after IGBT/Gate driver IC replacement

                thanks for the reply vinceroger69, that makes sense, and without the attitude
                Last edited by tech2014; 02-19-2016, 02:01 PM.

                Comment

                Related Topics

                Collapse

                • mikkele86
                  Power amplifier SMPS IGBT keeps blowing - Artcoustic PDA1000
                  by mikkele86
                  hello.

                  I have two power amplifiers, both having their IGBT blown on the PSU.
                  The original mounted IGBT where marked with IRGB20B60PD1PbF and the gate driver is a IR2156STRPBF.

                  I looked at mouser and digikey and could not find any available IRGB20B60PD1PbF and somehow ended up using a Bourns BIDW20N60T.
                  I replaced the gate driver, the gate resistor and both IGBT. But as soon power is turned on, both IGBT shorts out completely (gate, emitter, collector) and the fuse on the AC line gets killed.

                  So I though i missed a capacitor or diode. I removed...
                  01-06-2024, 06:45 AM
                • osrex
                  LED DRIVER KEEPS DYING
                  by osrex
                  Hello, this is my first post and im just a beginner, so be easy on me guy. thanks



                  i have a LED chandeilier that switches colors from white to cool white to warm when toggling the switch, it has 24 LED arms, each arm is 30 CM length.



                  i have no datasheet at all for the LED lights, all i have is its length.



                  long story short, testing the chandelier on the ground, and it works fine for 1 - 2 - 6 hours, no problem.



                  as soon as i fix the chandelier to the ceiling and bury the driver inside the hub,...
                  05-05-2025, 03:36 PM
                • tvguy12012012120
                  Zombie Samsung UN55NU6900F dead / no standby voltage - randomly came to life after hours of troubleshooting then died
                  by tvguy12012012120
                  This is my first attempt at troubleshooting a board like this, I know I could just buy a new board but I'm curious to figure out how this works. I've been testing different components in the evenings this week and I think the problem is with the IC failing to start up for some reason. When the board is plugged in there is no standby voltage.

                  Then today it randomly sprung to life like a zombie but shortly died thereafter. I have no idea why it would have done that and its the first time I've seen it running. I discharged capacitors on the board last night, then it was sitting today....
                  02-07-2025, 05:13 PM
                • repair-it
                  TOSHIBA DLP 52HM95 How to reset timer module on bulb
                  by repair-it
                  I replaced the bulb only on my Toshiba DLP The bulb is a TB-25. This is the first time I've done a bulb only replacement. Supposedly there is a timer module that needs to be re-calibrated or reset. I don't know where the module is located. I see some vendors selling the bulb with the housing stating module included which leads me to think the module is located inside the enclosure the bulb mounts in, but I didn't see it. Maybe it's inside the plug attached to the bulb?

                  Anyway - I am seeking information on how to reset this so called module so that the lamp will operate. Apparently...
                  10-11-2023, 07:18 PM
                • ezenia
                  LUMIMAN Smart Bulb IC ID?
                  by ezenia
                  Hi,

                  I have a LUMIMAN Smart Bulb that suddenly stopped lighting one day. The bulb is still detected in the app, but won't light. I've probed around and nothing seems to look off with any of the diodes, caps or resistors. The Bluetooth/Wi-Fi module seems to be working as it's still detected in the app. I even tried deleting and re-pairing the bulb (it didn't light, but I was still able to follow the pairing instructions), it re-paired fine, but still no light.

                  In diode mode, the LEDs all light up when probed so I'm guessing this means the LEDs themselves are OK. I was expecting...
                  04-28-2025, 05:56 PM
                • Loading...
                • No more items.
                Working...