Samsung ue40es600u no power

Mark845

Member

Join Date: Sep 2014

Posts: 10

Country: Durham
#1

Samsung ue40es600u no power

03-22-2015, 03:13 AM

My Samsung ue40es600u would not power this morning. So I've took the back of but i couldn't see anything that is burnt of anything like that. After I put the tv back together and plugged it in. It came on again but after I mounted it back on the wall it was not working again. I

The psu inside is a bn44-0051b.

I'm thinking the psu is on its way out . Would a simple psu replacement fix do you guys think? Or could it be something else.
Tags: None
Alastair E

Chief Womble

Join Date: Mar 2013

Posts: 1963

Country: U.K.
#2

03-22-2015, 04:24 AM

Re: Samsung ue40es600u no power

Take and post some clear pictures of the PSU, Mainboard and a shot of the whole TV chassis with the back off--Post 'em here.....

TELEFIX

How PLASMA SCREENS WORK, X-SUS and Y-SUS what they do--
http://www.irf.com/technical-info/appnotes/an-1088.pdf
PLEASE DO NOT EMAIL ME PRIVATELY FOR REPAIR ADVICE. QUESTIONS BELONG ON THE FORUM!
Comment

Previous template Next

Microsoft Surface Pro (5th gen) model 1796 - no power

by PantherDave

Hi all!

I'm trying to troubleshoot a Microsoft Surface Pro (5th gen) model 1796 that won't power on. Motherboard model is M1007506-015. My priority is retrieving data, but the SSD is integrated so it looks like if I can't repair it it'll need to go to a data recovery company. I've done a little basic board repair before, but nothing this advanced until now. So please forgive my ignorance in advance. 😅

I found the boardview for this laptop in the forums here, and am able to open it on my PC with FlexBV.
https://www.badcaps.net/forum/troubl...-hardware-devi...
- Channel: Troubleshooting Laptops, Tablets, and Mobile Devices
05-29-2024, 02:01 PM
Lift Master Garage Door wall switch display / motion sensor controller display disappeared no back light

by sam_sam_sam

This happened last Saturday and today I finally had time this morning before I went to work to replace two non brand capacitors

I will let you be the judge weather or not these are bad or not according to the blue ESR meter that I am using

I am comparing them to a brand new one that I installed

The display came back on and the programming was not lost which I was surprised by I would have thought that when the display went blank that so did the memory as well

I going to let it run for several days before I remount back on the wall next to the...
- Channel: General Electronics Technical Discussion
09-05-2024, 06:48 PM
Samsung TV won't turn on ... keeps cycling the power relay on & off

by Journey11

Hi All,
First time posting here ... my name is Kevin but my friends call me Journey.
I have a Samsung 75" LCD model UN75RU8000FXZA that I don't remember the original fault other than it wouldn't power up anymore.
After it sat for many month's I decide to look at it again. The motherboard seemed to have power regulation issues. After much fussing I decided to just get a new MB.
It came a few days ago and I installed it now just cycles the power relay on and off ... when on the backlights light up and then dim and then relay kicks off and the whole things starts again....
- Channel: Troubleshooting TVs and Video Sources
07-04-2024, 02:44 PM
Samsung un32j5205af turns on, but needs to have power disconnected to power back on

by thetonywarren

SAMSUNG UN32J5205AF

Wierd issue. Set turns on, works as normal, then turn off, and when you try to turn back on, it wont. The backlight comes on, but doesnt boot up. You need to disconnect power supply from back, then reconnect it, and then the set works again. somewhat annoying issue.

Where to start? I can provide any videos or pictures needed to troubleshoot.......
- Channel: Troubleshooting TVs and Video Sources
11-15-2022, 09:23 AM
Desoldering gun station modified to use a 18 volt @ 20 amp switching power supply

by sam_sam_sam

I have wanting to do this project for quite sometime now and I finally found a switching power supply that will work on this desoldering gun station ZD-915 that the original switching power supply took a shit and just was not worth trying to fix it because this switching power is not quite big enough to handle the heater element and the vacuum pump

One note when I tested the switching power supply and the voltage control board I noticed that this desoldering gun heat up much faster than the original switching power supply which I was really surprised by to the point that I might buy...
- Channel: General Electronics Technical Discussion
03-31-2024, 02:12 PM
Loading...
No more items.

Samsung ue40es600u no power

Samsung ue40es600u no power

Comment

Related Topics