New tool, Aoyue 8800! Desoldering just got easy!

[stj]

Re: New tool, Aoyue 8800! Desoldering just got easy!

i had a weller ds80, the cleaning is always a problem on vac tools.

to get the flux and other crap out of the end, use a drill-bit that is smaller than the hole when it's cold.
and if you use it a lot, empty the collector and inspect the filter atleast once a day.

[capkid]

Re: New tool, Aoyue 8800! Desoldering just got easy!

The Hakko 808 I bought was only $170 or $180. The only issue I've had is not an issue with the gun itself: The tips can become clogged and rendered unusable if you suck up flux. The flux becomes hard like concrete and is difficult to remove. I haven't found a removal method that doesn't also damage the tip. Also, I haven't encountered a need to have a station separate from the gun. What were your thoughts in that regard?

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

I hate to even have to revisit this thread and say this, but this thing is less than a month old and already has issues. The pump motor bogs down sometimes and then the suction is crap. I don't know if it's the motor itself, or just a bad connection. I haven't used it more than 10 times. I guess I'll tear it apart and see what it is. If you want one of these, I'd suggest saving up a bit more and getting a Hakko. Also, I think one where the pump is in a station rather than the gun would be better. Aoyue just lost me as a customer.

[Nerfinator]

Re: New tool, Aoyue 8800! Desoldering just got easy!

They could use a better label. It's not like this was cheap. $180, I think a foil label wouldn't cost more than a quarter.

That size, probably about .05/ea after volume pricing. I use to order custom foil labels from Uline for my concrete gnomes that my boys and I make.

[Nerfinator]

Re: New tool, Aoyue 8800! Desoldering just got easy!

WOW! I'm sold.

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

Maybe you should be glad, they might have used the money saved on the sticker to give it better quality wiring.

Good point.

[Agent24]

Re: New tool, Aoyue 8800! Desoldering just got easy!

Maybe you should be glad, they might have used the money saved on the sticker to give it better quality wiring.

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

They could use a better label. It's not like this was cheap. $180, I think a foil label wouldn't cost more than a quarter.

[Agent24]

Re: New tool, Aoyue 8800! Desoldering just got easy!

Wonder how long before Kada etc rip off the Aoyue!

Desoldering guns are pretty awesome compared to the one-shot pumps. But even those and braid are still good sometimes, desoldering gun doesn't work for everything.

I have a Den-On gun type one but I think I would prefer a station. I don't like the vibration from the pump motor. It seems to make it easier to damage pads sometimes.

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

So Aoyue finally ripped off the Hakko 808?

So it would seem.

[Agent24]

Re: New tool, Aoyue 8800! Desoldering just got easy!

So Aoyue finally ripped off the Hakko 808?

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

You can also add solder then suck up the solder on either side of the pin. You'll need lots of heat, so a heat gun is a must.

I have a heat gun. A remnant from my home improvement days. I use it, very carefully, to warm up boards so the heat doesn't disperse as quickly when I'm desoldering . I also have a hot air station.

[capkid]

Re: New tool, Aoyue 8800! Desoldering just got easy!

I bought mine from sra-solder, but through their eBay store because it was $10 cheaper there. I wish they made a tip that could fit over the pins on large heatsinks. I guess that's my only complaint, but from what I can tell, none of the other brands make such a tip either. Maybe I'll buy a spare 1.8mm tip and bore it out.

You can also add solder then suck up the solder on either side of the pin - this should clear the hole. You'll need lots of heat, so a heat gun is a must.

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

I bought mine from sra-solder, but through their eBay store because it was $10 cheaper there. I wish they made a tip that could fit over the pins on large heatsinks. I guess that's my only complaint, but from what I can tell, none of the other brands make such a tip either. Maybe I'll buy a spare 1.8mm tip and bore it out.

[capkid]

Re: New tool, Aoyue 8800! Desoldering just got easy!

http://youtu.be/mEgRHT1EqVA

http://youtu.be/aC0d-WhHdZM

[lookimback]

Re: New tool, Aoyue 8800! Desoldering just got easy!

How does it work? I use braid and pumps for my de-solder work but always looking for something to make it go faster. Time == $$$$

So far, I'd say it works really good.

[Nerfinator]

Re: New tool, Aoyue 8800! Desoldering just got easy!

How does it work? I use braid and pumps for my de-solder work but always looking for something to make it go faster. Time == $$$$

[capkid]

Re: New tool, Aoyue 8800! Desoldering just got easy!

Removed another IPM from an LG sustain board last night with the trusty paint remover. Jesus would one of these come in handy. Just about turned the board into charcoal in the process, will have to look into the proper tool for the job.

Yes, a desoldering gun makes removing IPMs MUCH easier. One thing I like to do when removing IPMs is to add a little solder to each pin before using the gun so that it flows better and the holes are cleaner. Also, I use a heat gun on a low setting to heat four to five pins at a time so the solder melts easier.

[ReeceyBurger123]

Re: New tool, Aoyue 8800! Desoldering just got easy!

This is going to make troubleshooting sustain boards so much faster. It comes with a nice storage case, but I think it will never see the inside of it again. I looked at the Hakko FR-300. This was about $80 less, and already $80 more than I intended to spend. My finger was literally hovering above the buy it now button for one of those S-993a guns, then I decided to look for some reviews on the 110v version. Glad I did.

Fair enough, I couldn't do half the repairs I preform with out it especially on things like motherboards ect.

[mmartell]

Re: New tool, Aoyue 8800! Desoldering just got easy!

Removed another IPM from an LG sustain board last night with the trusty paint remover. Jesus would one of these come in handy. Just about turned the board into charcoal in the process, will have to look into the proper tool for the job.