grundig 42 pw 110-5510 blink

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • topng
    Senior Member
    • Dec 2013
    • 56
    • ISRAEL
    #1

    grundig 42 pw 110-5510 blink

    hi all I need help

    I replace fsd200 and diode bridge and 2.2k ohm
    You will see a small fire on the side.

    the plasma is blinking no green led
    Tags: None
    • topng
      Senior Member
      • Dec 2013
      • 56
      • ISRAEL
      #2
      Re: grundig 42 pw 110-5510 blink

      this is the pic
      vs is ok
      va is ok
      5sb is ok
      all the voltage is fine so I think it is the video board .
      Attached Files
      Last edited by topng; 08-31-2014, 12:30 PM.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Ross Kohler
          Diagnosing South Bridge (FH82H370) on Asus H370-Pro Gaming Motherboard
          by Ross Kohler
          Hi,

          I'm learning about motherboard repair and I believe I've traced the issue down for the South Bridge on the particular motherboard I'm working on. My path of concluding that:
          - There's no sign of any attempt to power on when pushing the power button.
          - No PSON signal is reaching the 24-pin ATX connector.
          - The Super IO chip is receiving the PS_SWITCH signal from the power button and is relaying this signal back to the South Bridge.
          - The Super IO is not receiving the S_SLPS#_R signal back from the South Bridge
          - If I pull the Super IO S_SLPS#_R pin...
          04-16-2024, 09:36 AM
        • cloo
          Panasonic ZT60 plasma tv with strange behavior and 8 blink code
          by cloo
          I recently got my hands on a 60" Panasonic P60ZT60 plasma tv (european model) that has some strange issues along with an 8 blink code.
          It know this tv is getting old but it was once considered one of the best plasmas ever made, and i think it is still holds on to that even by todays standards.


          So, long story short. When i first got the tv it had a very bright washed out picture with very raised blacks in all picture modes and i couldn't find the cause in the picture setting menus.
          After doing a factory reset this problem was gone and the picture was back to...
          01-06-2025, 06:02 AM
        • EazyBone
          Un50cu7000 2 blink oddity *partially solved
          by EazyBone
          I write this to maybe help another with this TV.

          So I aquired this TV a 2023 model. It started the 2 blink reboot problem which indicates bad panel. It was still under warranty and the repair man came by.

          The Samsung repairman brought a brand new panel and switched my original boards to the new panel. The new panel then had the 2 blink error code. The repair guy said he has seen this and the MAIN board on this model will cause the 2 blink. He then replaced the main/power board (they are both connected) and put it back onto my original panel. Voila it worked.
          ...
          03-18-2024, 10:24 PM
        • Vebririon
          panasonic TX-P50V10E 6 blink led problem
          by Vebririon
          Hi everyone,

          I'm new here and trying to repair my Panasonic TX-P50V10E plasma TV, which is currently showing the 6 red blink error code.

          Just for context: I'm used to building PCs and installing modchips in old consoles, but this is my first time trying to fix a TV. I'm French, and while my English is okay, I'm using ChatGPT to help translate and clarify my messages as much as possible — so please forgive any odd phrasing.

          I'm also not very experienced with using a multimeter, but I'm very motivated and ready to follow instructions carefully and report...
          05-17-2025, 10:16 AM
        • Roman555
          Asus H77 LGA1155 mainboard stopped working with Ivy Bridge CPUs
          by Roman555
          Bad symptoms when Ivy Bridge CPU (3rd-gen 22nm) is installed:
          • Won't boot OS (just blank screen or stucks at asus logo, monitor is turned on) with hangs at debug (post) code A3;
          • USB stick with MS-DOS can be loaded via F8 boot menu;
          • Other OSes won't load - hangs or goes reboot;
          • Postponed for several seconds reaction to Alt-Ctrl-Del, Reset and Power buttons;
          • An operating system starts loading but won't finish if it's left only 1 CPU core in BIOS settings;
          What I've already done and it hasn't helped:
          • Cleared CMOS many times;
          • Flashed different versions of BIOS in a CH341 programmer;
          • Updated
          ...
          01-18-2024, 06:26 AM
        • Loading...
        • No more items.
        Working...