TV Sharp LC-49CFE6242E - not working - 2

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • betmen
    Senior Member
    • May 2019
    • 90
    • Croatia
    #1

    TV Sharp LC-49CFE6242E - not working - 2

    I wrote a topic earlier for this TV...https://www.badcaps.net/forum/troubl...2e-not-working
    I managed to fix the power supply but there are still some faults. The sound works a little and then doesn't work a little and the tv doesn't respond to the remote control at all (I've tried several remotes).
    I suspect the motherboard...is there anything that can be fixed or does it need to be replaced?​
    1 Photo
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4753
      • Russia
      #2
      Do you have a programmer that supports NAND Flash, if so, then read the dump of this NAND and post it here, I will check it and clear it of bit errors...
      Attached Files

        Comment

        • betmen
          Senior Member
          • May 2019
          • 90
          • Croatia
          #3
          Originally posted by lotas
          Do you have a programmer that supports NAND Flash, if so, then read the dump of this NAND and post it here, I will check it and clear it of bit errors...
          I don`t have NAND Flash programmer...
          Last edited by betmen; 01-06-2025, 08:14 AM. Reason: speling

            Comment

            Previous template Next

            Related Topics

            Collapse
            • betmen
              TV Sharp LC-49CFE6242E - not working
              by betmen
              Hello,
              I get one old TV, Sharp LC-49CFE6242E which is not working.
              When turning on the TV, the inscription SHARP is displayed on the screen and after a few seconds the TV turns off.
              So far I haven't found what voltages should be at the output of the power supply and I haven't made any measurements.
              If anyone has any ideas, please let me know.​
              Export Event
              Starts
              10-19-2024
              Ends
              11-19-2024
              10-20-2024, 08:44 AM
            • tranquility
              Onkyo TX-NR809 – no hdmi, DTS or NAND chip ? stuck at starting kernel
              by tranquility
              Hello,
              i want to repair an Onkyo TX-NR809 receiver.

              symptoms:
              on power on, display appears and i hear one click. enue functions is given.
              - no hdmi output
              - audio output not tested, but i think it is not there
              - usb sticks are not recognized

              if i read out the chips with display+standby button + tone+
              both dts show only ????

              chip is D830K013BZKB4

              things i have done:
              - reflow of the dts chip without taking off and reballing
              - changed the aluminium caps without the big one with 25v because i dont...
              08-25-2025, 01:04 AM
            • MarkC1970
              Nand dump needed for Sharp 32CHF5111K
              by MarkC1970
              Can anyone link me to a NAND dump for a Sharp 32CHF5111K. It is built using the TP.MS3463S.PB711 board, it has all 3 HDMI ports and no SPI chip.

              Thanks.
              02-22-2023, 11:13 AM
            • mattpd
              PS5 EDM-031 - Pulsing BLOD - SSD NAND chips never heat up
              by mattpd
              PS5 died in the middle of a game and never would boot again. Pulsing BLOD stays on forever but never boots.

              No LM damage. UART gives a generic "APU not responding" error.

              Under thermal camera, the SSD NAND chips stay stone cold. The controller warms, but not the NAND. I have a good 2.5v and 1.8v around the NANDs...

              I don't have a ton of PS5 experience, but I assume that the NAND would need to warm at least a little bit in order to boot...

              So to those with experience, would you expect at least a little heat from the NAND during...
              09-02-2025, 09:42 AM
            • MMH3
              Dell Optiplex 5050 SFF - strange behavior and service_mode jumper not working anymore
              by MMH3
              Hello,

              i have many 5050sff. all of them, and how i experienced over many years for all about 250 DELLs goin through my hands, are fully flashable and can be serviced in any way when the service_mode jumper is set.
              Never ever i experienced problems with that.

              Now i have one 5050sff machine, where this jumper isnt working at all.
              I do not get the normal messge that the jumper is set when booting and a short test with FPT just confirms this. Everything is locked -->> EVEN for reading !?

              The history of the machine is that i used it in my office...
              03-23-2025, 09:28 PM
            • Loading...
            • No more items.
            Working...