General MOSFET upgrade rules?

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Glitcher
    Badcaps Veteran
    • Mar 2013
    • 673
    • USa

    #1

    General MOSFET upgrade rules?

    Whats the typical rule when looking to replace a commonly failed FET with a different labeled FET in a power supply?
    Last edited by Glitcher; 01-03-2014, 09:58 PM.
  • Ltank
    Badcaps Veteran
    • Jun 2013
    • 776
    • USA

    #2
    Re: General MOSFET upgrade rules?

    Generally there are parts that will cross reference with other parts. There used to be cross reference books but generally are not available with today's search engines. Going with a part that has higher voltage and current ratings.

    Comment

    Related Topics

    Collapse

    • Jane
      How do you test MOSFET in laptops ?
      by Jane
      I tried to use this method:

      Testing an N-channel MOSFET:

      Step 1: Discharge the Gate (turn off the MOSFET)
      Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
      Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

      Step 2: Charge the Gate (turn on the MOSFET)
      Now, place the red probe on the Gate (G) and the black probe on the
      ...
      09-27-2024, 03:31 AM
    • Wolf1977
      general question when a mosfet on primary of transformer is burned
      by Wolf1977
      hi
      in a welding machine i had a mosfet and four components wich connect with it burned
      i ordered all the damaged components and replace it but when i put the device on the plug all the components burned again i had tested before and i had not shunts
      i dont understand whats happen wrong
      more particular on the schematic q11p01 mosfet q11p02 tranzistor
      three paralel resistors had burned q11p07 zener shunt q11p08 open
      when i changed all these shunts q11po7 mosfet and tranzistors
      maby the transformer has problem on your opinion or something on...
      08-19-2023, 01:27 PM
    • Nooy
      VGA MOSfet permanently shorted and loss of MOSfet pad
      by Nooy
      Hello everyone, I recently found this badcaps site and super Learn Electronics Repair youtube channel. And I wanted to learn how to troubleshoot power supplies and VGA cards and how to practice soldering, since I already have a properly defective piece of them. I am currently trying to solve two problems:

      I have a Gigabyte GV-RX460WF2OC-4GD type card. I managed to find the faulty MOSfet (AON6414A) on it, which I replaced. The card starts up, but after about half a minute, the MOSfet in the same position will be shorted again. Is it possible that the PWM controller driving the MOSfet...
      02-14-2024, 02:26 AM
    • AppleLover123
      Asus X712EA 3 volts after the first mosfet
      by AppleLover123
      Hey guys,

      i have a asus motherboard here and as the title says after the first mosfet (in the picture) there is nothing more than 3.15v.
      I injected 19v and max. 1 amp at the charging port and there is not voltage drop or smth. It's just taking 19v and 1 milliamp.
      Then i tried to inject 19v and max 1amp after the current sensor and there it first takes 19v and 4 milliamps and after 2 seconds it is taking nothing (no current).
      I measured on the coils on board everything seems fine. Also the main power rail is not shorted (infinite resistance).
      Now i thought something...
      12-15-2024, 07:49 AM
    • MicroSMD Lab
      ASUS ROG Zephyrus GPU Mosfet repeat failure
      by MicroSMD Lab
      The board number is GU502DU. I repaired this a couple weeks ago and it came back with the same issue, same mosfet failed (PQH9201). I'm hoping that the GPU was spared this time.
      I used the same replacement part (purchased from Mouser) and I'm certain the soldering was done properly since it took just as much effort to remove as before. What could cause this same mosfet to fail? I'm thinking if it was unsuitable then the others would fail too. I looked for similar failures on YTube and the mosfet was replaced with AOE6930 in one instance and AOE6932 in the other but it's possible that the...
      01-10-2024, 06:36 AM
    • Loading...
    • No more items.
    Working...