How do I remove a plastic split washer from a VHS VCR ?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • RolandVossen
    Member
    • May 2023
    • 11
    • Nederland
    #1

    How do I remove a plastic split washer from a VHS VCR ?

    Hi,

    I am trying to repair a JVC HR-D530E VHS recorder, the cassette does not eject. I discovered that the rubber belt of the loading motor is slipping, so I'd like to replace it. I think I have to remove the (nylon?) washers at each end of the worm axel, labeled '2' in the photo. I tried using a small screwdriver and a pair of tweezers, but to no avail.

    Is there perhaps a special tool or a trick required to remove these ?

    Thanks in advance, Roland.
    1 Photo
    Tags: vhs jvc
    • nomoresonys
      Badcaps Legend
      • Jan 2013
      • 12276
      • U.S.
      #2
      Should pop off without much trouble, maybe use a straight tip screwdriver to spread it a little.

        Comment

        Previous template Next

        Related Topics

        Collapse
        • howardc64
          A1312 (27” iMac 2009-2011) A1407 (Thunderbolt Display) A1316 (Cinema Display) Display Black Screen Repair
          by howardc64
          Problem

          This is an LG edge LED lit LCD Display. The LEDs are on the bottom edge of the display. There are 2 bars (left and right) Each bar has many LEDs and a 6 pin connector. Each pin drive several LEDs thus is the highest current flow / heat junction. The weak lead free solder gradually fails with thermal expansion/contraction cycling and increases resistance. PSU will compensate up to a point, then when the current is too high, PSU just shut down the backlight causing a dark display. I have even seen one which the connector just fell off as solder points became completely detached....
          08-04-2024, 10:36 PM
        • Kemer
          Led status indicator light transfer plastic
          by Kemer
          Hello, the LED status indicators on my Lenovo Z580 are not working. Actually the motherboard LEDs are working but the light doesn''t coming to the front view. The plastic part is which you can see in photo must transfer the light to the frontview but just half of the plastic is illuminating.

          There are three status indicators on the front (power, battery, caps lock), and none of them are illuminated.

          The plastic piece doesn't appear to be broken.

          1. What are your suggestions for resolving this issue?

          2. Is the plastic piece made of special ma...
          08-19-2025, 07:02 PM
        • acedogblast
          Guide to transplant MEC1503 EC chip and EEPROM reprogamming for T14s gen 2 and X13 gen 2
          by acedogblast
          This is a guide that I am writing for helping others to replace their MEC1503 EC chip if it breaks (or to get around an inconvenient prompt to the BIOS). This forum has been extremely helpful to me so I would like to contribute to help others. I will tell you right now that this task is very difficult to do. You MUST have experience and tools to do precision micro-soldering, BGA reballing, trace repair, and general laptop repair skills.

          There are some specialty tools needed to do this task. The replacement MEC1503 chips can be acquired from Aliexpress. Do not buy the bare chips as...
          11-02-2024, 05:13 PM
        • Document Archive
          Mounting and Handling Guidelines for TO220 TO220F TO247 Cases / Packages
          by Document Archive
          Mounting and Handling Guidelines for TO220 TO220F TO247 Cases / Packages

          The TO220, TO220F and TO247 are the popular packages for power devices because of their versatility and ability to dissipate moderate amounts of heat. This application note describes the basic guidelines for handling power MOSFETs in TO220, TO220 and TO247 packages shown in Figure 1. Please note that only mechanical and soldering guidelines are covered here. Additional precautions are required for isolating high voltage rated devices to meet safety regulations.

          Securing a good thermal interface between...
          10-07-2024, 04:35 AM
        • longmt1990
          Panasonic Cf-w5 bios password remove
          by longmt1990
          Hi, i have a Panasonic Cf-W5 with the bios password, I tried remove cmos but problem didnot solve.
          I uploaded the picture after remove cmos battery, It look like this is a Phoenix bios. The bios dump file in the link i attached

          Please help me remove bios password.
          Thank you so much
          07-06-2025, 10:50 PM
        • Loading...
        • No more items.
        Working...