colby tftv3227

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • tocold4u2
    Badcaps Veteran
    • Dec 2012
    • 284
    • usa

    #1

    colby tftv3227

    I have a colby 32". That will power on but will say l
    lost signal n will power off after awhile. after.opening the set up it acts like a short .while open with the set on the "no signal" stays on..plays fine. when i go to close the unit up the "no signal" starts to flicker in and out..all wires/connectiins are tight. pic s will be hard cause im posting this with my cell phone .
  • newtothis
    Badcaps Legend
    • Mar 2013
    • 1556
    • england

    #2
    Re: colby tftv3227

    check grounds

    Comment

    • tocold4u2
      Badcaps Veteran
      • Dec 2012
      • 284
      • usa

      #3
      Re: colby tftv3227

      Ty for the reply...that was my first thing i checked. these tv s r cheaply made..and thrown together

      Comment

      Related Topics

      Collapse

      • AstutePauciloquent
        Requesting Help For GA-970A-DS3 rev. 1.0, No Post code, no RSMRST# signal
        by AstutePauciloquent
        Hi everyone, over the past few months i have taken a deep dive into motherboard diagnostics and I love the challenge. Currently im trying to learn all about the signals that travel around the motherboard, such as frequencies, enable signals High and Low logic states etc. And i have been learning to read and using the Schematics for this board that i requested here on Badcaps forum, from a few months ago, this is such a great place for these.

        I’ve been working on a GA-970A-DS3 (rev. 1.0) that does not post. This motherboard has been my main learning board. I would like share...
        11-23-2023, 11:02 PM
      • howardc64
        Vizio M65Q7-H1 Red Vertical Strips fixed by tape blocking LC1 signal to half of the panel
        by howardc64
        Failure Symptom



        No picture, just red vertical stripes. Google search shows quite common problem for these recent Vizio M series although red vertical stripe pattern may differ. Some call it "Netflix" boot screen haha.

        Where is the short?

        Panel has 4x buffer boards. Quickly found the 1/4 panel buffer board with the problem by selectively disconnecting buffer board flex cables.



        Having recently fixed another Vizio with similar symptoms that was a shorted ESD diode array ( link ) Probed the ESD diode array but...
        05-27-2025, 02:56 PM
      • JayPoorJay
        Converting +/- 5v to a Usable Hz Signal
        by JayPoorJay
        Good morning.

        I have posted here before and have gotten AMAZING advise (thank you!). I'm back for more. This BCaps Sub Forum is so well attended I thought I would post here.

        This question is for an automotive application but has to do with what are essentially electrical questions and problem solving... If this is inappropriate I get it. Feel free to delete it or move the question.

        The V 12 Jaguar XJS is notorious for overheating in stop and go traffic in hot weather... Y'all will be potentially helpinh a LOT of people. The solutions and directions...
        08-07-2022, 08:35 AM
      • Scruit
        What is a normal composite signal range for a C64?
        by Scruit
        Hello all,


        Working on my first C64 / Breadbin / 250407. Purchased as non-working. Getting black screen.


        More detail below, but for those that want to get right to the question.... Here are a few waveforms comparing the Pin15 output on the VIC chip (luma/sync) to the pin 4 on the AV socket (composite signal).

        https://imgur.com/gallery/PpqcqPY


        My question is: Is the composite waveform range of 0.1v-1v too low for a c64?



        More detail:


        Symptoms are that that I get...
        04-28-2022, 05:33 AM
      • supravit2000
        PS4 fat has inconsistent signal after HDMI replacement
        by supravit2000
        Hi, guys!

        I am not a professional, all I can do is solder stuff on the boards, so I would really appreciate it if someone with knowledge shares his experience/thoughts on a problem I have with a PS4 console.

        My friend gave me an original fat PS4, board model SAB-001, with WLOD, that has been previously opened. I changed the HDMI port, couple of pads on the board were ripped, which I connected to the corresponding caps/resistors? Just did so as in a shown diagram (one of the ground pads I ripped off and left it not connected). However, there was still no signal, so...
        12-19-2022, 08:08 PM
      • Loading...
      • No more items.
      Working...