panasonic lcdTH-L32C20M

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • willyam1
    Senior Member
    • Feb 2012
    • 112
    • israel
    #1

    panasonic lcdTH-L32C20M

    HI to all.
    problem is by powering red stb led become green and then click and red led again and it blinks 10 times.
    is it the pfc section in the p.s the problem .
    p.sTNP4G469.
    MAIN-TNP4G466.
    WILLYAM1
    Tags: None
    • willyam1
      Senior Member
      • Feb 2012
      • 112
      • israel
      #2
      Re: panasonic lcdTH-L32C20M

      anyone?help..........
      willyam

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Andre Gilbert
          Panasonic TC-P55ST50 8 blinks then no blinks
          by Andre Gilbert
          Hello! yes I know there is already lots of information about this issue. I have a Panasonic TC-P55ST50 that originally displayed an 8-blink error code. Following the troubleshooting flowchart, I ended up replacing the SS board. However, even after replacing it, the issue persists. The TV turns on and stays on without displaying an image, and continuity is confirmed on all connectors. What am I missing hereπŸ€”?
          Ok Im a mechanical engineer ...but I thought I was able to follow a rather simple flowchart for electric troubleshooting πŸ˜‚.

          TV Model: Panasonic TC-P55ST50
          ...
          1 Photo
          11-20-2024, 08:52 PM
        • jm1234
          Panasonic plasma TX-P42ST50 - 6 blinks
          by jm1234
          Hi,
          anyone able to provide the service manual for old plasma Panasonic TX-P42ST50E?
          It turns off almost immediately (0~5 seconds after pressing the on/off button) and starts flashing the red diode 6 times.
          I disconnected the left-hand side board (SC?, both the ribbon cable and the power cable to it) and also another ribbon going to bottom left board. Then the led signal is 8 flashes. According to service guide to another Panasonic plasma it would mean the left-hand side board is faulty. But I'm not sure it 100% applies to my model.
          I checked that board for any obvious faults...
          05-22-2024, 06:59 AM
        • CrewmanRedShirt
          Looking for assistance troubleshooting a Panasonic TC-P65ZT60 with 3 LED Fast Blinks
          by CrewmanRedShirt
          Hello all,
          As the title states, I followed the troubleshooting guide located here: https://www.manualslib.com/manual/23...page=53#manual, which concluded the 'A' board needs to be replaced. Looking around the net and eBay, I see that there are repair services for the board (TNPH1043UE? Not sure if it is a 'UE' as the suffix grid does not appear marked). What additional troubleshooting can be performed to ensure 1) this board is the problem and 2) since there are repair services, what are they fixing on the board?) I expected 3.3V not to be available anywhere...
          07-13-2024, 11:02 AM
        • nobbnobb1
          Panasonic TC-P50U50 Powers Off - 8 blinks
          by nobbnobb1
          Hello,

          I have a Panasonic TC-P50U50 plasma TV which powers on briefly, then powers off and flashes the power light with 8 blinks. This TV is infamous for this, of which the suggestion that the SS board has failed due to loose grounding screws and requires a replacement of the following components on the SS board:

          2x DG302 (Q16051)
          2x RF2001 (D16041)
          2x 5.6 ohm SMD resistor
          1x BD8694 IC

          I have already gone ahead and replaced these components, as well as cleaning off the ground connections on the SS board as well as the associated...
          03-21-2023, 08:33 PM
        • mmischni
          Panasonic Viera Plasma TH-42PX75U 7 Blinks/8 Blinks/burned P board?
          by mmischni
          Greetings friends,

          I have a Panasonic TH-42PX75U manufactured in 2007. It has been trouble-free until recently. One evening I turned it on and it then powered back off and gave 7 blinks.

          First a question about the blinks. Everyone only speaks of a single number of blinks. I noticed on my TV, it blinks one fewer times for the first group of blinks, then blinks the full number repeatedly. So for my first code in question, the TV switches off, blinks 6, then blinks 7 repeatedly. When I disconnected the SC board, the TV switches off, blinks 7, then blinks 8 repeatedly....
          09-06-2017, 08:52 PM
        • Loading...
        • No more items.
        Working...