Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Try 200 ohm range (no "k").
Try 200 ohm range (no "k").
-
Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search. -
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
ok, so i tried that and i get a quick flash of digits then i just sits on what i think is infinite resistance (1.) the reading i get is the same as i get when both connections on the multi meter are not touching each other. does that make senseComment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Can you show me where you are probing?Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Last edited by joehezzer; 02-09-2013, 07:31 AM.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Those are the correct resistors. They should measure 4.7 ohm. But if they are all failed I would suspect the plasma panel drivers.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
I wonderd because this board had gone down
[/QUOTE]
That it may have shorted the longer bottom board. I suppose i am just defo ruling out every other possible out come. And the panel is defo brokeComment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
The X-main (large right board) can't cause that.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
1.65 ohm (may read 1.6 or similar) might be reasonable.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
Yes quite possibly.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
I do appreciate your help dude . At least i know the power supply workslolComment
-
Re: Another Philips 50PFP5532D 50" 1080i HD Plasma Television
And the Y-main, Y-buffers, video board, control board and X-main.Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
For service manual, schematic, boardview (board view), datasheet, cad - use our search.Comment
-
Hello guys,
My Plasma Philips 37inch chassis FTL2.1 does no picture ,and goes into protection mode after 30 seconds (red led blinks at 3Hz).
Can someone has any symptom like this ?
Thanks05-09-2024, 10:56 PM -
Hi,
I am attempting to repair my television. When I turn it on, it seems to start normally and then the backlight turns off after a couple seconds.
Initially on the main power board I replaced diode D1202 which was shorted, and capacitor C1201 which was bulging. I was still getting some wonky voltages, so also replaced C1204, C1250 on the main board, as well as the filter caps on the LCD module, which were 3 680uf caps in parallel, which I replaced with 2 1000uf caps in parallel.
The tv is still showing the same symptoms, although now... -
hello,
I hope someone on this forum can assist me.
I have a panasonic TH-42PC77U plasma television.
the lower 1/2 of the screen has become flaky....in and out, then finally goes black and you can only see the top portion.
i have performed the reset to default settings quite a few times. Panasonic recommended..did not believe this would help...it didn't.
I have removed the back panel and looked around for something obvious...burn marks in a board, etc....nothing obvious...
I have read some posts that suggest the problem is related to the boards on the left... -
Philips 8200 series 65PUS8204/12 stuck at Philips Logo, it does not reboot it just stays on the logo.
It does power up when pressing the power button.
I already try the power button while plugin the plug with no result.
Also put the latest firmware autorun-TPM191E_R.001.004.100.000.upg on a MBR/FAT32 USB stick at USB port2 with no result either.
Could this be an PSU or eMMC issue ? -
Hi all,
Wife has 2 Philips hair curling irons half defective - after learning how they're supposed to work and testing them, it turned out that both have defective power cables, and both on the same place; broken wires due to wire bending.
As they were both relatively easy to disassemble, and cables are plugged not soldered (as they can rotate in the handle), I was sure it would be easy to find replacements. But - NO! I'm unable to find anything similar on ebay or Aliexpress.
Not sure if this is something Philips proprietary, or a standard, but the cable plug...
Comment