Announcement

Collapse
No announcement yet.

Onei 26av400

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    #61
    Re: Onei 26av400

    Yes.
    Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
    For service manual, schematic, boardview (board view), datasheet, cad - use our search.

    Comment


      #62
      Re: Onei 26av400

      Tom check all of the ones i changed and dont seem to be any reading

      Comment


        #63
        Re: Onei 26av400

        Also whilst tv was on i disconnected the block wiring from the vestel to the 17mb45m board and the flashing stopped ? is this normal

        Comment


          #64
          Re: Onei 26av400

          Yes, that is normal. It is dead without the main board. Since it is not powering up at all I suspect the main board. I cannot be sure though.
          Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
          For service manual, schematic, boardview (board view), datasheet, cad - use our search.

          Comment


            #65
            Re: Onei 26av400

            what about the main power blocks on the vestel ?

            Comment


              #66
              Re: Onei 26av400

              Not sure what you mean?
              Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
              For service manual, schematic, boardview (board view), datasheet, cad - use our search.

              Comment


                #67
                Re: Onei 26av400

                the biggish blocks black/yellow

                Comment


                  #68
                  Re: Onei 26av400

                  Transformers. Don't often fail.
                  Can you access the pins of PL816 on power board? It's the connector going to the main board.
                  In particular, check pin 14 and pin 16.
                  Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                  For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                  Comment


                    #69
                    Re: Onei 26av400

                    yes can access pl816 looks ok,

                    Comment


                      #70
                      Re: Onei 26av400

                      Check the pins I indicated above then.
                      Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                      For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                      Comment


                        #71
                        Re: Onei 26av400

                        with the multimeter ? with the set on and wiring plug in ?

                        Comment


                          #72
                          Re: Onei 26av400

                          Multimeter, 20V DC, set plugged in with blinking light.
                          Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                          For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                          Comment


                            #73
                            Re: Onei 26av400

                            do you put both leads on one or one each on 14 and 16

                            Comment


                              #74
                              Re: Onei 26av400

                              One on 14, other on ground, read voltage.
                              One on 16, other on ground, read voltage.
                              Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                              For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                              Comment


                                #75
                                Re: Onei 26av400

                                ok and switch to the v- symbol

                                Comment


                                  #76
                                  Re: Onei 26av400

                                  Volts DC, usually V=
                                  Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                  For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                  Comment


                                    #77
                                    Re: Onei 26av400

                                    14 nothing, 16 0.72

                                    Comment


                                      #78
                                      Re: Onei 26av400

                                      That does not make sense. You have a flashing LED right?
                                      Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                      For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                      Comment


                                        #79
                                        Re: Onei 26av400

                                        switched on-flashing,theres 14 to a row,checked 14 could not get a reading,then on the second row number 16 was reading 0.72 ?

                                        Comment


                                          #80
                                          Re: Onei 26av400

                                          They are probably ordered

                                          1 2
                                          3 4
                                          5 6

                                          etc.

                                          Pin 1 will be labelled, often pin 2 too as well, or the last pin, just a matter of deducing the right pin.
                                          Please do not PM me with questions! Questions via PM will not be answered. Post on the forums instead!
                                          For service manual, schematic, boardview (board view), datasheet, cad - use our search.

                                          Comment

                                          Working...