LG 60pn6506 Plasma

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • An-klamm
    Member
    • Feb 2023
    • 43
    • Deutschland

    #1

    LG 60pn6506 Plasma

    Hello!

    Have received a LG 60pn6506 60 inch from a work colleague.
    RJP30H2A on the X-Board were shorted.
    60R5_YSUS, EAX64789501 and EBR75455701 is written on the board.
    New board for about 130$ is too much for him. So if that's the only option, that's going on the scrap (after the PSU and Y board are sold).
    I checked the area around the RJP Mosfets and found that the diodes on the gate pin are also defective (for Example D564). Imprint is: UF and then 90° offset CD. In Diodetestmodes the good ones show ~0,2V

    A little further to the right on the board, two parts with the SOT23-5 housing are also cracked (IC404 and IC403) on the IC403 I could still read the label (is only cracked on the side) 5K was written on it. I assume its some kind of dcdc converter.

    Does someone have the schematics or a similar board?
    Attached Files
  • R_J
    Badcaps Legend
    • Jun 2012
    • 9558
    • Canada

    #2
    Re: LG 60pn6506 Plasma

    The sot23-5 (5K) are likely Toshiba HN4B101J

    Comment

    • An-klamm
      Member
      • Feb 2023
      • 43
      • Deutschland

      #3
      Re: LG 60pn6506 Plasma

      Replaced the broken parts.
      Found 15V missing.
      Replayced the parts mentioned in this thread https://www.badcaps.net/forum/showthread.php?t=69738 (post 12)

      Seems like all voltages are present (if I have not overlooked anything) but TV does not start (even just patterntest via "TCON" does not start)
      "TCON" flashes 3x short 1x long

      Voltages measuared:
      printed vs. measuared
      PSU
      17V 17V (to mainboard)
      M5V 5,2V 5,2V
      VA 55V 55V
      VS 202V 202V

      ZSUS
      18V 17,8V
      17V 17,8V
      VS 202V 202V
      5V 5,2V
      VZB unknown 108,4V

      YSUS
      15V 17,8V
      VS 202V 202V
      5V 5,1V
      VSC unknown 150V

      Comment

      Related Topics

      Collapse

      • ArMaaN376
        Samsung PS51E550 Plasma TV
        by ArMaaN376
        Hello,
        I am having Samsung PS51E550 Plasma TV. While the TV was working, a crackling sound heard & video went off with audio still ON. After switching it off & ON, the red LED on TV blinks six times & then off.
        Opened TV cover & observed foll
        a) Green LED on the small PCB blinks at @5-6sec ON & off for 3-4 secs. Red LED on logic board ON
        b)Vs & Va on power supply board raises momentarily to 209v & 58v resp & then drops.
        c) Cold test on Y-main board shows all 3 pins of FGPF4536 IGBT short to Grnd.
        How to confirm Y -Buffer board...
        06-19-2024, 04:05 AM
      • jm1234
        Panasonic plasma TX-P42ST50 - 6 blinks
        by jm1234
        Hi,
        anyone able to provide the service manual for old plasma Panasonic TX-P42ST50E?
        It turns off almost immediately (0~5 seconds after pressing the on/off button) and starts flashing the red diode 6 times.
        I disconnected the left-hand side board (SC?, both the ribbon cable and the power cable to it) and also another ribbon going to bottom left board. Then the led signal is 8 flashes. According to service guide to another Panasonic plasma it would mean the left-hand side board is faulty. But I'm not sure it 100% applies to my model.
        I checked that board for any obvious faults...
        05-22-2024, 06:59 AM
      • KYBOSH
        Hitachi 55HDS69 55" Plasma TV - No Picture But Sound
        by KYBOSH
        Picked up a bahemoth plasma TV not too long ago and just now getting around to looking at it.
        No picture but you hear the TV static (white noise) playing loud and clear.
        The back was already taken off (and no screws were provided) as the previous owner had already taken a look.
        But it seems they didn't get too far and just left it.

        When I first took a look I was amazed at how pristine the inside looked.
        Its as if the TV had been in a time capsule.
        Caps looked like they were just pulled off the self.
        Copper coils had no sign of corrosion on...
        02-01-2023, 11:10 PM
      • porfyriadhs
        Samsung Plasma PS51D6900DS Bootloop
        by porfyriadhs
        Hello . I have a problem with a samsung plasma tv stuck in bootloop . The TV is Samsung PS51D6900DS plasma smart tv .Need help if anyone have any suggestions
        Thanks a lot !!
        10-19-2023, 11:31 AM
      • SurrealMustard
        What parts can be salvaged from a plasma with a damaged display panel?
        by SurrealMustard
        I recently found myself the proud owner of a later-model Samsung plasma (the PN59D7000 for those keeping score at home) whose panel was, unfortunately, damaged in transport. I'm now preparing to part it out, but am curious as to whether or not any damage would have come to any of the components by attempting to power it up with the panel being broken. I read in one Avsforum thread (for whatever that's worth 😂) that the "scan driver boards" (by which I assume he means buffer boards) could be impacted by doing so. Is that actually the case? If so, since I don't intend on selling bad...
        03-09-2025, 08:29 PM
      • Loading...
      • No more items.
      Working...