PANASONIC TX-L42EW6K sinc error

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • hugmax
    New Member
    • Mar 2023
    • 8
    • Spain
    #1

    PANASONIC TX-L42EW6K sinc error

    This tv I masked some lines on the right flex to block clk and now it has this problem.
    The left side is very slow to refresh.



    https://www.facebook.com/10000215023...1464075559576/
    Attached Files
    Tags: None
    • Davi.p
      Hobbist Tech
      • Sep 2009
      • 4463
      • Italy - Milan
      #2
      Re: PANASONIC TX-L42EW6K sinc error

      there's a problem with vgl/vgh lines, maybe bad contact, try first disconnecting one ribbon at a time of tcon outputs and notice wich one presents the major symptoms

        Comment

        Previous template Next

        Related Topics

        Collapse
        • Sus256
          HISENSE 65E7KQ PRO - no boot
          by Sus256
          Hi all!

          HISENSE 65E7KQ PRO
          RSAG7.820.13512 - chassis
          MT9618BAATAB - cpu
          RSAG7.820.12059 - power
          HD650Y3U77 - panel
          KLM8G1GETF - emmc

          The TV does not turn on, the standby indicator is on. All voltages are present.
          Emms is dead. Not readable, not detected.
          Replaced emmc.
          But with another dump there is no launch

          Terminal log

          UART
          <
          AC_ON
          RPMB key is not yet programmed

          HASH1_VERSION=0x00000000 64bit
          E-B
          FDE enabled
          layout pattern onebin by SAR7,0...
          06-01-2025, 02:11 AM
        • sushilachuthan
          APC UPS error P13
          by sushilachuthan
          one of our new (only 4 year old) 1KVA APC UPS stop working and through error P13 contact customer support.
          the equipment is out of warranty , upon investigation, we found the inverter board has the fault on the output hybrid relay circuit.
          The inverter output relay is parallel by SCR/Triac to enhance the relay performance or other means.
          We replaced the SCR with new device,, but the device is not power on as expected.

          Further research on the issue found that, the error P13 (event ID 107) is latched on the UPS nvram/MCU and need to clear/reset using a service procedure....
          09-26-2025, 09:00 AM
        • Superbee_dad
          Sharp 80” long short flash backlight error - Help
          by Superbee_dad
          Hello Sharp TV experts
          Our Sharp LC-80LE642U displays one short one long flash error code which is a backlight error. I went into service mode and there were 8 lamp error counts recorded. I reset the count to 0 and did a reset. The last monitor error cause was 16 B00014639:12. 16 is the code for backlight error. I tried to power the tv up but went back into error mode.

          > I checked voltages on the power supply board and they all check out .. including 3.28 volts at the error pin.
          > There is power to the cpu and T-CONN and no faults found there. The cpu has a flashing...
          01-24-2025, 11:51 PM
        • Curtissimo
          HP EliteBook 850 G8 - Error code / Caps Lock permanently on and blinks twice every 6 seconds
          by Curtissimo
          Hi everyone.

          I have a HP Elitebook 850 G8.
          Serial: 5CG2324XM0
          ProdID 6L8D5EC#ABA
          It has a Winbond W25Q256JVEN Chip.

          I need to remove BIOS Password.

          I made a dump with an CHA341A programmer and NeoProgrammer 2.2.0.10.

          Attached my dump.

          I also used the HP Unlocker tool to create an unlocked file (I followed the guidelines)

          I also downloaded latest HP BIOS Update (SP158137) which includes 3 .bin files. I found the Number T76 in my original dump, so I used: T76_01210000.bin

          What I did:...
          08-26-2025, 04:42 AM
        • nervx
          Panasonic TH-42PZ800 8-blink error mystery
          by nervx
          Years ago my tv gave a 7 blink code which turned into 8 during diagnosis. I had ordered a replacement ss board but somehow the tv started working again and i never used the board. Now a week ago my tv flickered and shut off at random and gave the 8 blink error code. The same issue it had all those years ago. The only difference this time is that over the last few months there has been some purple and green tinge that comes and goes in more solid colors such as white.

          Anyway i checked all the screws and replaced the ss board with a known good one and still got 8 blinks. I saw a...
          04-08-2022, 05:19 AM
        • Loading...
        • No more items.
        Working...