matrix printer,help identify smd fuse

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • JoeBug
    Member
    • Jul 2015
    • 20
    • Bulgaria
    #1

    matrix printer,help identify smd fuse

    hello,
    i have this matrix printer, there are fuses for the pins on the head, one is open but i am not able to identify it and find replacment. its marked just NB, F3 on the board (red circle)
    the printer is EPSON LX-350
    Attached Files
    Last edited by JoeBug; 10-29-2021, 06:12 AM.
    Tags: None
    • lotas
      Badcaps Legend
      • Jan 2016
      • 4562
      • Russia
      #2
      Re: matrix printer,help identify smd fuse

      Nb - 1.6a
      Attached Files

        Comment

        • JoeBug
          Member
          • Jul 2015
          • 20
          • Bulgaria
          #3
          Re: matrix printer,help identify smd fuse

          Originally posted by lotas
          Nb - 1.6a
          10x a lot man!

            Comment

            Previous template Next

            Related Topics

            Collapse
            • jshhh
              Help replacing fuse on my Mimaki CJV300-160 vinyl printer
              by jshhh
              Hi guys,

              I'm inexperienced with electronics repairs, I've done a little bit of soldering caps and whatnot, but i have a blown fuse on this mimaki printer I got which I have bought a replacement for.

              How do I remove this type of fuse (see picture)...it kinda looks like it would pull out of that bracket but it didn't come at first pull and I didn't want to brute force it incase it's soldered on there like most of the rest of the components.

              Anybody know how to remove this type of fuse?

              (The fuse is toward the bottom of the image labeled F2)...
              06-17-2025, 01:35 AM
            • Francesc V.
              Help me to identify this Thermal fuse from my sister's mixer
              by Francesc V.
              Hi everyone:

              This is the second time I have my sister's mixer on the bench. First time I identified a blown tiristor......this time I guess it's the thermal fuse (reads open).

              My understanding is that it should be (NC) normally closed and open at 85C?????

              Could you help me to identify/get a good one? How many amps? I was about to buy a NC 10A, 85 celcius in Aliexpress. (ceramic one)......but I guess is too much.

              Wording in the back......... "limitor 16", "T160".


              Thanks in advance,
              Francesc....
              03-18-2025, 05:48 AM
            • re-atari
              Anycubic Photon 5.5 3D printer 25Q32 flashrom dump needed
              by re-atari
              Hello all, as the title says, I'm very much in need of a valid firmware dump of a Anycubic Photon 5.5 3D resin printer. It's stored in a Winbond 25Q32, so it's 4Mbyte.

              Here's a little background for my request. A few weeks ago I bought this 3D printer from a guy who had moved on to a PLA printer. I got it at a vey reasonable price, as it was in a defective state. The seller told me that he had experienced a power failure during a firmware upgrade, after which the printer appeared to be dead. He thought the firmware was corrupted in such a way that the printer was now bricked. As he...
              02-03-2025, 06:49 PM
            • corrize
              A funny fuse story – Lumix LX100 II
              by corrize
              Hello, I disassembled this dead camera, and found this WTF… Two fuses soldered one above the other !
              I was pretty sure nobody touched it before, but that can't be from factory. There is flux, and capacitor is probably missing.
              The other weird thing : the fuses are « G » fuse : (0.75A – 8V), seems very low. The original fuse should be « O » : (32V 2,5A).
              There is « O » mark beside. All fuses have the same mark letter on main board. So, I can deduce it's a « O » fuse.
              And this correspond to the issus I saw : when I plug the battery, I measure the voltage dropping...
              10-19-2023, 09:58 AM
            • Curious808
              Brother HL-2140 laser printer: printer error (solved)
              by Curious808
              SOLVED. I removed the printer in settings, replugged and let it reinstall and it worked this time.

              Brother HL-2140 laser printer
              Windows 10

              Attempt to print and immediately get a Windows pop-up saying "Error printing". The document appears in the printer queue window with Status "Error-printing".

              Turned off printer. Unplugged, waited, replugged. Ran the Windows troubleshooter. Removed and reinserted toner cartridge. Checked for paper jam. No printer error lights. Reinstalled driver. Restarted the Spooler service. Rebooted...
              06-22-2023, 11:11 PM
            • Loading...
            • No more items.
            Working...