ATP-1655 mosfet equivalents

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • seanc
    Badcaps Legend
    • Nov 2008
    • 1319
    #1

    ATP-1655 mosfet equivalents

    I have one of he above power supplies from an ASUS Terminator PC.

    A Mitsubishi FS7KM mosfet has popped in it - I suspect either due to conductive glue syndrome or because of the bad Teapo in it.

    I've scraped the remaining brown glue away.

    On hand, I have a 2SK2843 which seems to exceed the specifications of the FS7KM, it does have a lower RDS ON though. Will it work?

    At my disposal I also have: STPS20100CT or FCF10A60.

    Cheers!
    Attached Files
    Tags: None
    • everell
      Badcaps Legend
      • Jan 2009
      • 1514
      • USA
      #2
      Re: ATP-1655 mosfet equivalents

      I am not familiar with this particular power supply. Some pictures would help.

      The STPS20100CT and FCF10A60 are dual rectifiers, so they will definitely not substitute for the FS7KM. The 2SK2843 might work - might not. Is the FS7LM FET that blew in the 5vsb circuit or is it the main switching transistor, or perhaps one of two main switching transistors. Need more information please.
      Old proverb say.........If you shoot at nothing, you will hit nothing (George Henry 10-14-11)

        Comment

        • seanc
          Badcaps Legend
          • Nov 2008
          • 1319
          #3
          Re: ATP-1655 mosfet equivalents

          Pictures attached

          The 5VSB purple wire is over the other side of the board near the 3 Nichion caps, so I'd guess it's not part of that circuit.

          Seeing as it's next to the primary capacitors and a 2.2uf 50v cap, I would say it's in the primary section.
          Attached Files

            Comment

            • seanc
              Badcaps Legend
              • Nov 2008
              • 1319
              #4
              Re: ATP-1655 mosfet equivalents

              I just fixed this.

              I took the suspicious FS7KM out and examined it - it wasn't damaged, it was just well cooked glue. Scraped the glue off and it tested fine. Put it back in - still no go.

              I dug around scraping the glue off of the rest of the board and found a lone mosfet I'd missed earlier, hiding under the 5v wires. It was all covered i brown glue.
              Took it out, cleaned off the crusty glue and corrosion - put it back in and it's working

                Comment

                Previous template Next

                Related Topics

                Collapse
                • Jane
                  How do you test MOSFET in laptops ?
                  by Jane
                  I tried to use this method:

                  Testing an N-channel MOSFET:

                  Step 1: Discharge the Gate (turn off the MOSFET)
                  Place the black probe (COM) on the Source (S) and the red probe on the Drain (D). The multimeter should show no continuity (high resistance or "OL" – open line).
                  Then, touch the black probe to the Source (S) and the red probe to the Gate (G). This discharges any stored charge in the Gate, turning the MOSFET off.

                  Step 2: Charge the Gate (turn on the MOSFET)
                  Now, place the red probe on the Gate (G) and the black probe on the                  ...
                  09-27-2024, 03:31 AM
                • Nooy
                  VGA MOSfet permanently shorted and loss of MOSfet pad
                  by Nooy
                  Hello everyone, I recently found this badcaps site and super Learn Electronics Repair youtube channel. And I wanted to learn how to troubleshoot power supplies and VGA cards and how to practice soldering, since I already have a properly defective piece of them. I am currently trying to solve two problems:

                  I have a Gigabyte GV-RX460WF2OC-4GD type card. I managed to find the faulty MOSfet (AON6414A) on it, which I replaced. The card starts up, but after about half a minute, the MOSfet in the same position will be shorted again. Is it possible that the PWM controller driving the MOSfet...
                  02-14-2024, 02:26 AM
                • AppleLover123
                  Asus X712EA 3 volts after the first mosfet
                  by AppleLover123
                  Hey guys,

                  i have a asus motherboard here and as the title says after the first mosfet (in the picture) there is nothing more than 3.15v.
                  I injected 19v and max. 1 amp at the charging port and there is not voltage drop or smth. It's just taking 19v and 1 milliamp.
                  Then i tried to inject 19v and max 1amp after the current sensor and there it first takes 19v and 4 milliamps and after 2 seconds it is taking nothing (no current).
                  I measured on the coils on board everything seems fine. Also the main power rail is not shorted (infinite resistance).
                  Now i thought something...
                  12-15-2024, 07:49 AM
                • MicroSMD Lab
                  ASUS ROG Zephyrus GPU Mosfet repeat failure
                  by MicroSMD Lab
                  The board number is GU502DU. I repaired this a couple weeks ago and it came back with the same issue, same mosfet failed (PQH9201). I'm hoping that the GPU was spared this time.
                  I used the same replacement part (purchased from Mouser) and I'm certain the soldering was done properly since it took just as much effort to remove as before. What could cause this same mosfet to fail? I'm thinking if it was unsuitable then the others would fail too. I looked for similar failures on YTube and the mosfet was replaced with AOE6930 in one instance and AOE6932 in the other but it's possible that the...
                  01-10-2024, 06:36 AM
                • Scotchmist
                  Asus GA502D keeps blowing mosfet
                  by Scotchmist
                  I have an Asus GA502D, it had a blown mosfet which I replaced and the laptop booted into windows, a few mins later it shut off, the same mosfet was blown. I thought maybe just a bad mosfet but same thing happened again, a few mins in windows and shuts off.

                  I have removed the mosfet and can run the laptop no problem

                  The MOSFET is FDPC5018SG

                  Can anyone point me in the direction of what could be the cause of this, could it be the controller rt3663bc?

                  Thanks
                  08-24-2024, 02:23 PM
                • Loading...
                • No more items.
                Working...